Extralite CH-01 Computer Mount

Discuss light weight issues concerning road bikes & parts.
Post Reply
coresare
Posts: 104
Joined: Thu Jun 18, 2015 8:19 am

by coresare

Got the mentioned mount. Wasn't expecting much. Initially I thought it looked kinda unpolished/industrial? When I first twisted the Garmin 510 on I was greeted with a loud and satisfying *Snap* as it locked firmly into place. It was so nice I had to do it a few more times. Before I used the Raceware mount and that one doesn't lock the computer into an exact position which was okay because the mount doesn't line up perfectly straight. The CH-01 is perfectly aligned. The looks also grew on me also and I like it a lot. After subtracting the weight of the clamps it comes to about 13 grams which is 1 gram lighter than the Raceware.
Attachments
20190612_132431.jpg
20190612_132348.jpg
20190612_132311.jpg
20190612_132253.jpg
20190612_132243.jpg
20190612_131107.jpg

Johnny Rad
Posts: 1964
Joined: Fri Feb 17, 2006 6:22 am
Location: Zion

by Johnny Rad

Nice write-up.

Think Extralite's deisgn could readily be made into a double-sided version? So I can mount a Fabric Lumaray light underneath and a Garmin on top?

by Weenie


User avatar
Klaster_1
Posts: 720
Joined: Mon Aug 15, 2016 10:25 am
Location: Russia

by Klaster_1

Johnny Rad wrote:
Sat Jun 15, 2019 2:08 am
Think Extralite's deisgn could readily be made into a double-sided version? So I can mount a Fabric Lumaray light underneath and a Garmin on top?
I already thought of that and asked Extralite. They kept silent about the light mount idea, but shared safe weight limit you can load it with - about 250g. CH-01 base has four holes in it, so it should be possible to bolt custom fixtures on both sides.

sychen
Posts: 568
Joined: Thu Apr 24, 2014 1:06 pm

by sychen

Klaster_1 wrote:
Johnny Rad wrote:
Sat Jun 15, 2019 2:08 am
Think Extralite's deisgn could readily be made into a double-sided version? So I can mount a Fabric Lumaray light underneath and a Garmin on top?
I already thought of that and asked Extralite. They kept silent about the light mount idea, but shared safe weight limit you can load it with - about 250g. CH-01 base has four holes in it, so it should be possible to bolt custom fixtures on both sides.
Also asked this when the mount was first announced... And they did reply that they were considering it.

I would most definitely get a hyperstem and a mount if it can take a light /camera underneath.



Sent from my Pixel 2 XL using Tapatalk


coresare
Posts: 104
Joined: Thu Jun 18, 2015 8:19 am

by coresare

It doesnt look like an easy solution to mount a GoPro style mount at the bottom for a light. I'll attach a photo of the bottom. My Barfly mount had preexisting threaded holes at the bottom that worked perfectly for a K-Edge GoPro mount. I suppose you could custom drill holes into the GoPro mount and use those two horizontal holes in the "bridge" at the front of the Extralite mount.

It does look nice and clean with a bottom GoPro mount for a light, but in all honesty I would rather just attach a light onto the handlebar with the supplied rubber straps since most of the time I'm not using a light.
Attachments
20190614_212631.jpg
20190614_212605.jpg
20190614_212531.jpg

ironman1
Posts: 194
Joined: Thu Dec 09, 2004 5:51 pm

by ironman1

Have Extralite out front mount and it is rock solid side to side but slight flex front to front. On looking when locked in there is small gap 1/16 inch between computer (520 ) and mount . Just enough to cause a vibration and annoying buzz on rough roads. Any one else experience same problem ?

coresare
Posts: 104
Joined: Thu Jun 18, 2015 8:19 am

by coresare

No noise or buzz here

by Weenie


garjo
Posts: 194
Joined: Thu Aug 13, 2015 8:41 pm
Location: ITALY

by garjo

ironman1 wrote:
Sun Jun 30, 2019 4:29 pm
Have Extralite out front mount and it is rock solid side to side but slight flex front to front. On looking when locked in there is small gap 1/16 inch between computer (520 ) and mount . Just enough to cause a vibration and annoying buzz on rough roads. Any one else experience same problem ?
put a piece of cut plastic bag between your device and the mount and rotate your device, it should work
My 4,93 kg Supersix Evo HM: viewtopic.php?f=10&t=137647&start=30

My 6,22 kg Cannondale R500 1996: viewtopic.php?f=10&t=134364

Post Reply
  • Similar Topics
    Replies
    Views
    Last post