Tillquist's kitchen!

Discuss light weight issues concerning road bikes & parts.
chocy
Posts: 73
Joined: Sun Dec 19, 2010 5:30 am
Location: New York City

by chocy

Tillquist,

I just e-mailed you about 3T ARX version.

Thanks!
------------------------------------------------
My Colnago EPS http://weightweenies.starbike.com/forum/viewtopic.php?f=10&t=83064&start=45

tomaz69
Posts: 55
Joined: Tue May 12, 2009 11:09 am

by tomaz69

hi - can you tell something about handling with garmin on this holder? As it is a bit lower than with original holder and closer to the handlebar - is there any problem to press buttons on use touchscreen?

thx

User avatar
CBJ
Posts: 1060
Joined: Tue Feb 02, 2010 4:22 pm
Location: Brooklyn

by CBJ

I have the 3T holder. It easy to reach everything.

Tillquist
Posts: 1593
Joined: Fri Dec 30, 2005 3:33 pm
Contact:

by Tillquist

CBJ wrote:I have the 3T holder. It easy to reach everything.


Just my word :-)
See all my bike h e r e

petal666
Posts: 865
Joined: Fri Dec 12, 2008 5:19 am
Location: Brisbane, Oz
Contact:

by petal666

petal666 wrote:Looks like the ritchey wcs 4 axis has had a bolt width change at some stage. My new mount doesn't fit.

There are 2 versions of Ritchey stems available, one with a wider bolt patter for extra stiffness which is what I have. 2 new stems on their way. :D

gaisdergerman
Posts: 18
Joined: Thu Aug 11, 2011 11:10 am

by gaisdergerman

I ordered a mount the same time as I ordered my canyon.
This week I noticed that the mount doesn't fit. Unfortunately I can't run another stem on this canyon.

I mailed tilquist about it if I can change it for another mount so I can use the mount on a other bike. So far I don't have a answer :-(

Edit: a had a good proposal from tilquist. Thanks!

Verstuurd vanaf mijn GT-I9105P met Tapatalk
Last edited by gaisdergerman on Thu Jan 16, 2014 8:43 am, edited 1 time in total.

Tillquist
Posts: 1593
Joined: Fri Dec 30, 2005 3:33 pm
Contact:

by Tillquist

Image

Image

Garmin mount for new Giant Contact SLR one piece stem/bar
See all my bike h e r e

Tillquist
Posts: 1593
Joined: Fri Dec 30, 2005 3:33 pm
Contact:

by Tillquist

gaisdergerman wrote:I ordered a mount the same time as I ordered my canyon.
This week I noticed that the mount doesn't fit. Unfortunately I can't run another stem on this canyon.

I mailed tilquist about it if I can change it for another mount so I can use the mount on a other bike. So far I don't have a answer :-(

Verstuurd vanaf mijn GT-I9105P met Tapatalk


I have send you a mail.....
See all my bike h e r e

FIJIGabe
Posts: 1400
Joined: Tue Sep 11, 2012 6:07 pm
Location: The Lone Star State

by FIJIGabe

Hey Tillquist, I sent you an e-mail regarding Bontrager RXXXL stems. They're 22mm. I don't know if you have anything in that spec.
Madone 9 https://goo.gl/7UwZpV
Crockett https://goo.gl/f5PdCN
Madone 5 https://goo.gl/cMdyFo

Madone 4, Cobia. I own a lot of Treks.

nigel379
Posts: 108
Joined: Sat Jun 20, 2009 3:23 am

by nigel379

I too am interested in the Bontrager xxx lite stem (newest model). The only issue is that the face plate has more of a curve than most (especially compared to 3T arx stem).

RichieE46
Posts: 48
Joined: Sun Aug 18, 2013 4:54 am

by RichieE46

Received my mount yesterday for my Zipp stem. Great quality. Thanks a ton!

Looks so much better than the K-edge mount that I had.

szazbo
Posts: 54
Joined: Mon Sep 18, 2006 6:26 am

by szazbo

I am finally getting around to hopefully getting a picture posted. Stem is a Moots Ti stem and I had Tillquist modify the Garmin mount so that the center was not machined all the way through. Plan was to mount the Di2 junction box on the bottom, which worked out great. I took the stock 11 speed mount and cut the tabs off with a razor knife giving me a flat surface. Then some epoxy to hold the Di2 mount to the Tillquist mount. Junction box is easily snapped off if needed. Charging port is easy to get too. Also since the stem cap bolts are recessed the outside diameter of the Tillquist mount fits into the recess in the stem cap. These were measurements that I provided when ordering. I did have the mount anodized black, as it came painted. Great guy to work with.

Image

Image

User avatar
carbonLORD
in the industry
Posts: 394
Joined: Fri Jan 23, 2004 6:31 pm
Contact:

by carbonLORD

Very nice! Looks like I'll be doing that as well (once I build up my 11 speed crit bike in April) making my 3rd Tillquist mount. Good work.
carbonLORD.com

gaisdergerman
Posts: 18
Joined: Thu Aug 11, 2011 11:10 am

by gaisdergerman

Received my zipp mount today and install it. When I mount my garmin on the mount there is no click. Is this normal?

For the rest a great mount.

User avatar
carbonLORD
in the industry
Posts: 394
Joined: Fri Jan 23, 2004 6:31 pm
Contact:

by carbonLORD

gaisdergerman wrote:Received my zipp mount today and install it. When I mount my garmin on the mount there is no click. Is this normal?

For the rest a great mount.


Correct, no click.
carbonLORD.com

Post Reply