2020 Specialized Tarmac SL7

[ome rodriguez]

My scale is accurate

[ryanw]

So are mine

61cm Satin Carbon / Jet Fuel.

[floriansantana]

Sorry if this has been discussed before but I couldn’t find anything using the search function.

It seems to be possible to use a SRAM BB30 crankset with BSA30 bottom bracket, as long as it’s the one with removeable spider. Can anyone tell me, what the exact setup would be then? Do I need any spacers? Do I need to remove the preload adjustment ring and replace it with a wave washer?

Please help me out. Thanks in advance!

I'm running it on my SL7 with the kogel BB.

Drive Side: No spacers
Non-Drive Side: i think I have a 2mm spacer (see pic)

Thanks a lot! Are you using some kind of wave washer RO get some preload? Or just tighten it up? No chance to keep the preload adjuster as it gets too tight?

[Takeswood]

Here SL7 Frame 10R in tropical teal : 867gr in 54. I find it light for non s-works bike and painted compared to a more raw paint.

Do you know where I can find screw for front derailler hanger ? Because one of them has damage on screw head recess and I don't want to fail to remove it when it tightened

Pictures of my frame here :

[K4m1k4z3]

Do you know where I can find screw for front derailler hanger ? Because one of them has damage on screw head recess and I don't want to fail to remove it when it tightened

Nice weight. I've got the same frame. ^_^

The FD mount comes with the 2 little screws and the whole thing can be ordered through a Specialized dealer:
S201900003
DER MY21 TARMAC SL7 FRONT DERAILLEUR HANGER W/BOLTS

[Takeswood]

Do you know where I can find screw for front derailler hanger ? Because one of them has damage on screw head recess and I don't want to fail to remove it when it tightened

Nice weight. I've got the same frame. ^_^

The FD mount comes with the 2 little screws and the whole thing can be ordered through a Specialized dealer:
S201900003
DER MY21 TARMAC SL7 FRONT DERAILLEUR HANGER W/BOLTS

Ah ! Beautiful colour, but yeah it's blue/green and not everyone's taste
Thanks for reference of hanger. I measured these 2 screws and I think it's M3x10. Ti bolt ordered on AliE
And if it isn't correct size, I will order your ref at my LBS. Thank you !

[kppolich]

Sorry if this has been discussed before but I couldn’t find anything using the search function.

It seems to be possible to use a SRAM BB30 crankset with BSA30 bottom bracket, as long as it’s the one with removeable spider. Can anyone tell me, what the exact setup would be then? Do I need any spacers? Do I need to remove the preload adjustment ring and replace it with a wave washer?

Please help me out. Thanks in advance!

I'm running it on my SL7 with the kogel BB.

Drive Side: No spacers
Non-Drive Side: i think I have a 2mm spacer (see pic)

Thanks a lot! Are you using some kind of wave washer RO get some preload? Or just tighten it up? No chance to keep the preload adjuster as it gets too tight?

No preload. It won't fit.
1 spacer, torque to spec, adjust spacer width as needed.

[bikeaddict314]

Is it possible to fit a 30mm tire in the SL7? The specialized website mentions 28mm and bike blogs are saying it has room for 32mm. I'm trying to figure out if I should stick with 28mm or move to 30mm.

[zmjones]

Is it possible to fit a 30mm tire in the SL7? The specialized website mentions 28mm and bike blogs are saying it has room for 32mm. I'm trying to figure out if I should stick with 28mm or move to 30mm.

yes

[BikeTyson]

Is it possible to fit a 30mm tire in the SL7? The specialized website mentions 28mm and bike blogs are saying it has room for 32mm. I'm trying to figure out if I should stick with 28mm or move to 30mm.

I have GP4000 that measure 31mm and they fit with a lot of room.

[franckydet]

Sorry if this has been discussed before but I couldn’t find anything using the search function.

It seems to be possible to use a SRAM BB30 crankset with BSA30 bottom bracket, as long as it’s the one with removeable spider. Can anyone tell me, what the exact setup would be then? Do I need any spacers? Do I need to remove the preload adjustment ring and replace it with a wave washer?

Please help me out. Thanks in advance!

I'm running it on my SL7 with the kogel BB.

Drive Side: No spacers
Non-Drive Side: i think I have a 2mm spacer (see pic)

Thanks a lot! Are you using some kind of wave washer RO get some preload? Or just tighten it up? No chance to keep the preload adjuster as it gets too tight?

No preload. It won't fit.
1 spacer, torque to spec, adjust spacer width as needed.

Hello, is it possible to mount the S-Works Power Cranks – Dual-Sided crankset like the sram BB30 crankset?

[franckydet]

sorry duplicate

[mlosco]

I am currently running 30mm Vittoria Corsa Controls on Roval Rapide CLX rims, and they also fit with plenty of room. I don't have calipers, so I don't have a measured width.

[DaiD]

Hi there,

Looking at buying the S-Works Tarmac stem for a different bike, but I can't find the width/height dimensions of it. I need to see if the stem will work with the cable routing spacer [i.e. be wide enough to cover it, and high enough with the cut steerer tube] on the bike I'd be using it with. Could anybody help with these measurements? Many thanks!!

[floriansantana]

I'm running it on my SL7 with the kogel BB.

Drive Side: No spacers
Non-Drive Side: i think I have a 2mm spacer (see pic)

Thanks a lot! Are you using some kind of wave washer RO get some preload? Or just tighten it up? No chance to keep the preload adjuster as it gets too tight?

No preload. It won't fit.
1 spacer, torque to spec, adjust spacer width as needed.

Hello, is it possible to mount the S-Works Power Cranks – Dual-Sided crankset like the sram BB30 crankset?

I don’t think it is, because the spindle of the S-Works crankset is too short.