Extralite CH-01 Computer Mount
Moderator: robbosmans
Got the mentioned mount. Wasn't expecting much. Initially I thought it looked kinda unpolished/industrial? When I first twisted the Garmin 510 on I was greeted with a loud and satisfying *Snap* as it locked firmly into place. It was so nice I had to do it a few more times. Before I used the Raceware mount and that one doesn't lock the computer into an exact position which was okay because the mount doesn't line up perfectly straight. The CH-01 is perfectly aligned. The looks also grew on me also and I like it a lot. After subtracting the weight of the clamps it comes to about 13 grams which is 1 gram lighter than the Raceware.
-
- Posts: 2025
- Joined: Fri Feb 17, 2006 6:22 am
- Location: Zion
Nice write-up.
Think Extralite's deisgn could readily be made into a double-sided version? So I can mount a Fabric Lumaray light underneath and a Garmin on top?
Think Extralite's deisgn could readily be made into a double-sided version? So I can mount a Fabric Lumaray light underneath and a Garmin on top?
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
I already thought of that and asked Extralite. They kept silent about the light mount idea, but shared safe weight limit you can load it with - about 250g. CH-01 base has four holes in it, so it should be possible to bolt custom fixtures on both sides.Johnny Rad wrote: ↑Sat Jun 15, 2019 2:08 amThink Extralite's deisgn could readily be made into a double-sided version? So I can mount a Fabric Lumaray light underneath and a Garmin on top?
Also asked this when the mount was first announced... And they did reply that they were considering it.Klaster_1 wrote:I already thought of that and asked Extralite. They kept silent about the light mount idea, but shared safe weight limit you can load it with - about 250g. CH-01 base has four holes in it, so it should be possible to bolt custom fixtures on both sides.Johnny Rad wrote: ↑Sat Jun 15, 2019 2:08 amThink Extralite's deisgn could readily be made into a double-sided version? So I can mount a Fabric Lumaray light underneath and a Garmin on top?
I would most definitely get a hyperstem and a mount if it can take a light /camera underneath.
Sent from my Pixel 2 XL using Tapatalk
It doesnt look like an easy solution to mount a GoPro style mount at the bottom for a light. I'll attach a photo of the bottom. My Barfly mount had preexisting threaded holes at the bottom that worked perfectly for a K-Edge GoPro mount. I suppose you could custom drill holes into the GoPro mount and use those two horizontal holes in the "bridge" at the front of the Extralite mount.
It does look nice and clean with a bottom GoPro mount for a light, but in all honesty I would rather just attach a light onto the handlebar with the supplied rubber straps since most of the time I'm not using a light.
It does look nice and clean with a bottom GoPro mount for a light, but in all honesty I would rather just attach a light onto the handlebar with the supplied rubber straps since most of the time I'm not using a light.
Have Extralite out front mount and it is rock solid side to side but slight flex front to front. On looking when locked in there is small gap 1/16 inch between computer (520 ) and mount . Just enough to cause a vibration and annoying buzz on rough roads. Any one else experience same problem ?
put a piece of cut plastic bag between your device and the mount and rotate your device, it should workironman1 wrote: ↑Sun Jun 30, 2019 4:29 pmHave Extralite out front mount and it is rock solid side to side but slight flex front to front. On looking when locked in there is small gap 1/16 inch between computer (520 ) and mount . Just enough to cause a vibration and annoying buzz on rough roads. Any one else experience same problem ?
My 4,93 kg Supersix Evo HM: viewtopic.php?f=10&t=137647&start=30
My 6,22 kg Cannondale R500 1996: viewtopic.php?f=10&t=134364
My 6,22 kg Cannondale R500 1996: viewtopic.php?f=10&t=134364
Be careful, I did something similar to my raceware mount. Additional pressure broke off the tabs of my edge 510 years ago.garjo wrote: ↑Mon Jul 01, 2019 3:09 pmput a piece of cut plastic bag between your device and the mount and rotate your device, it should workironman1 wrote: ↑Sun Jun 30, 2019 4:29 pmHave Extralite out front mount and it is rock solid side to side but slight flex front to front. On looking when locked in there is small gap 1/16 inch between computer (520 ) and mount . Just enough to cause a vibration and annoying buzz on rough roads. Any one else experience same problem ?
2018 Giant TCR Advance SL0 Disc
2017 Festka Scalatore
1989 Battaglin Roche
1985 Alan Carbonio
2017 Festka Scalatore
1989 Battaglin Roche
1985 Alan Carbonio
Extralite said they would cover it under warranty but I'm not messing around with international shipping. Just the adhesive failed, there was hardly any holding it all toether. There is a small groove on either side of the detached piece. They fit together like a lego so it was easy to line them back up. I just used some JB Weld Kwik Weld to glue it all back together, used just enough pressure with the clamp to hold it all together while curing. It's rock-solid now after a couple of hours of drying time.
- CarbonWorks
- Posts: 72
- Joined: Sat Jan 19, 2019 12:03 pm
Hi,
due to the fact, many of you asking again and again
....we have finished a CarbonWorks mount for Extralite.
Angle of the Computer is adjustable!!!
GoProAdapter is available!!!
Length is adjustable in 4 positions!!!
Perfect symmetry design!!!
...hope you are satisfied.
Thank you!
due to the fact, many of you asking again and again
....we have finished a CarbonWorks mount for Extralite.
Angle of the Computer is adjustable!!!
GoProAdapter is available!!!
Length is adjustable in 4 positions!!!
Perfect symmetry design!!!
...hope you are satisfied.
Thank you!
Simon
carbonworks.de
carbonworks.de
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
- MrCurrieinahurry
- Moderator
- Posts: 4825
- Joined: Wed Apr 22, 2020 3:01 pm
- Location: London
And the weight is? Ps nice to have u around CW..
Sent from my MAR-LX1B using Tapatalk
Sent from my MAR-LX1B using Tapatalk
Formerly known as Curryinahurry