New cannondale SYSTEMSIX road frame!

[lazyriderzhao]

Just finish my build

viewtopic.php?f=10&t=161245

[hannawald]

looks really sharp!

[tanbrett87]

For those that run fully integrated mechanical setups through the handlebar, stem and head tube:

1.) Did you use an aftermarket cable system like Alligator iLink or Jagwire Elite Link to make the tight bends through the cockpit?

2.) Can you use the BB cable guide as a cable stop for the derailleurs (and rear brake if you’ve got mechanical discs)? I think I read that someone did this but can't remember where I saw this, if it was this thread or elsewhere.

3.) How is the real world shifting performance? I’m planning on building with Campy SuperRecord 11spd with a Quarq PM and have heard the front derailleur can be finicky during shifts from small to big ring.

I've read Damon's response that this routing is possible, just not endorsed by Cannondale and that there is some degradation in shifting performance.

Thanks for the input!

[Unniti]

Does the SystemSix have clearance problems with 12 speed? The SuperSix thread has reports of clearance issues with AXS. One of the local shops has a scorching deal on a 2019 Ultegra model. If I were to buy it I'd strip the frame for 12 speed Campy.

[Dan Gerous]

Does the SystemSix have clearance problems with 12 speed? The SuperSix thread has reports of clearance issues with AXS. One of the local shops has a scorching deal on a 2019 Ultegra model. If I were to buy it I'd strip the frame for 12 speed Campy.

The chain is not on the 10t cog but, looks like clearance is okay on this SystemSix with red AXS.



I'm not sure if Campagnolo have moved/widened their 12 speed cassettes outboard compared to 11 speed like SRAM did though, I thought they didn't, leaving the 11t cog on their 12 speed cassette exactly at the same place the 11t cog was on their 11 speed cassette.

[req110]

deleted

[req110]

deleted

[req110]

deleted

[req110]

I am selling also frameset, it's 56cm Hi-Mod, the one from my topic.

If you are interested leave me a PM with your email. I am shipping from Czech Republic, probably only within European trade area.

[floriansantana]

Selling a Raceware Wahoo ELEMNT Bolt Mount for SystemBar or SaveBar, because I’m switching to an ELEMNT Roam (and already ordered the mount for that). It’s perfectly new and looks a 1000 times better than the one from Cannondale.

PM if interested.

[floriansantana]

Can someone who owns a SystemSix EF frame in size 56 (or 54) give me the measurement for the Cannondale font-logo on the downtube? I’d need the full length, the height of the font (probably of the „d“ or the „l“) and where it starts (measured from the BB).

Thanks in advance, need it for a custom paint job.

[woodyvalentine]

Can someone who owns a SystemSix EF frame in size 56 (or 54) give me the measurement for the Cannondale font-logo on the downtube? I’d need the full length, the height of the font (probably of the „d“ or the „l“) and where it starts (measured from the BB).

Thanks in advance, need it for a custom paint job.

About 323mm x 43mm is the font and about 10mm from the edge of the BB

[floriansantana]

Can someone who owns a SystemSix EF frame in size 56 (or 54) give me the measurement for the Cannondale font-logo on the downtube? I’d need the full length, the height of the font (probably of the „d“ or the „l“) and where it starts (measured from the BB).

Thanks in advance, need it for a custom paint job.

About 323mm x 43mm is the font and about 10mm from the edge of the BB

Cool, thanks. But just to be sure: You mean 100mm (10cm) from the edge of the BB, right? 10mm seem very strange.

[woodyvalentine]

Can someone who owns a SystemSix EF frame in size 56 (or 54) give me the measurement for the Cannondale font-logo on the downtube? I’d need the full length, the height of the font (probably of the „d“ or the „l“) and where it starts (measured from the BB).

Thanks in advance, need it for a custom paint job.

About 323mm x 43mm is the font and about 10mm from the edge of the BB

Cool, thanks. But just to be sure: You mean 100mm (10cm) from the edge of the BB, right? 10mm seem very strange.

Yes sorry. 10cm / 100mm from edge of BB.

[danridesbikes]

changed from Roval CL64 to Knot64 & Saddle to S-Works Power, also switched out the Axles to Robert Axle Project






gif upload site