Page 1 of 1
Low stack top cap for Trek Emonda
Posted: Sat Dec 02, 2017 1:41 pm
by Geordiepaul
I'm trying to fine the lowest possible stack headset bearing cover for an Emonda.
Currently have an FSA cover that's 10mm. Was hoping to get something 5mm'ish, however it's proving difficult as the bearing sticks out of the frame a couple of mm. So the with the slam that stem ones you can see the bearing.
Can anyone recommend something with a good fit?
Re: Low stack top cap for Trek Emonda
Posted: Sun Dec 03, 2017 2:50 am
by SilentDrone
I have considered same, and asked at the local trek store. They said it’s no problem to fit a 5 mm. Gave me the impression they have them in stock.
Sent from my iPhone using Tapatalk
Re: Low stack top cap for Trek Emonda
Posted: Sun Dec 03, 2017 2:50 am
by Weenie
Visit
starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
Re: Low stack top cap for Trek Emonda
Posted: Sun Dec 03, 2017 1:18 pm
by Geordiepaul
I'll ask my local dealer then..
Low stack top cap for Trek Emonda
Posted: Sun Dec 03, 2017 6:42 pm
by SilentDrone
Let us know what you find. I did some googling and it looks like the standard cone is 15mm and FSA has a “short” 9mm cone so maybe what you have is the shortest. Anyway, I’m curious to know how you solve this. Best.
Sent from my iPhone using Tapatalk
Re: Low stack top cap for Trek Emonda
Posted: Sun Dec 03, 2017 9:42 pm
by Geordiepaul
The standard cone shaped cap is 20mm
Re: Low stack top cap for Trek Emonda
Posted: Mon Dec 04, 2017 6:16 pm
by Fisherfreerider
Keep in mind Trek recommends a 5mm spacer above and below the stem including the bearing cover.
http://www.bike-manual.com/brands/trek/ ... 0701PN.pdf
Re: Low stack top cap for Trek Emonda
Posted: Mon Dec 04, 2017 9:19 pm
by Windstopper
Geordiepaul wrote:I'm trying to fine the lowest possible stack headset bearing cover for an Emonda.
Currently have an FSA cover that's 10mm. Was hoping to get something 5mm'ish, however it's proving difficult as the bearing sticks out of the frame a couple of mm. So the with the slam that stem ones you can see the bearing.
Can anyone recommend something with a good fit?
Check out slam that stem
Sent from my iPhone using Tapatalk
Re: Low stack top cap for Trek Emonda
Posted: Mon Dec 04, 2017 10:24 pm
by FIJIGabe
Cane Creek just released their new Slamset headset. It's claim 2mm stack height. I think this is what you're looking for:
https://www.canecreek.com/store/headset ... 41-top-167
Re: Low stack top cap for Trek Emonda
Posted: Tue Dec 05, 2017 5:23 pm
by Geordiepaul
Hmmm I suppose it depends if that bearing is designed to sit fully in the frame or not.
Re: Low stack top cap for Trek Emonda
Posted: Tue Dec 05, 2017 5:23 pm
by Weenie
Visit
starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
Re: Low stack top cap for Trek Emonda
Posted: Tue Dec 05, 2017 5:44 pm
by FIJIGabe
There's a new bearing that goes with it, the Hellbender, which helps lower the stack to that low level.