Weight Weenies

@kode54

Sure that is something I can work on, just give me a couple of days.

WheresWaldo wrote: ↑

Tue Jul 13, 2021 12:35 pm

@kode54

Sure that is something I can work on, just give me a couple of days.

THat's great! Will order 2. I changed stems...and this mount has that 22mm spacing which is NOT the K-Edge standard 20mm bolt spacing. Odd. Thx!

Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓    Broad Selection ✓    Worldwide Delivery ✓

www.starbike.com

Bud,

Just a FYI...I bought the 3T Strada Varia mount for seatpost. The holes are made for an M4 not a M5 that is required to bolt up to the back of the seatpost. Also, the countersunk holes are too small (probably because it is 3D printed for a M4 and not M5).

@kode54, thanks for the heads up, I will fix it and reupload a new model. I also shoould have your Di2 model done tomorrow.

WheresWaldo wrote:@kode54, thanks for the heads up, I will fix it and reupload a new model. I also shoould have your Di2 model done tomorrow.

Great. I will reorder the Strada Varia post mount as well. Thx again.

@kode54

Something like this, https://a360.co/36H6Hjq

35 mm diameter
3 mm overall base thickness
22 mm hole spacing for M3 flat head socket screws w/taper
60° outside chamfer

Are these the dimensions you wanted?

I will upload both this and the fixed Strada mount at the same time.

WheresWaldo wrote: ↑

Fri Jul 16, 2021 1:24 pm

@kode54

Something like this, https://a360.co/36H6Hjq

35 mm diameter
3 mm overall base thickness
22 mm hole spacing for M3 flat head socket screws w/taper
60° outside chamfer

Are these the dimensions you wanted?

Perfect! Thx Bud!

WheresWaldo wrote: ↑

Fri Jul 16, 2021 1:36 pm

I will upload both this and the fixed Strada mount at the same time.

Great! Much appreciated.

@kode54 here they are.

http://shpws.me/SKxq
http://shpws.me/SBP9

Great! Thx Bud.

So the 3T Strada seatpost Varia mount has been updated? The link takes me back to the original one. LMK.

Yes, Shapeways website is kinda strange. They do not deal with iterations very well, so even though it is the new corrected version it might still show the previous version on screen. They will always be at the same link. Their servers take their time re-rendering unless I force it to re-render and that is hit or miss.

Here is how Shapeways handles iterations, lets say I model something, call it RevA, you order RevA, then I revise it and upload RevB, even if I upload it 60 seconds after your order you still get RevA, if it is misprinted (Shapeways fault) and they agree to reprint, it will always be RevA. Now if you place a new order after I upload RevB, you will always get RevB, even if you wanted RevA or any subsequent revision, and so on. It is convaluted but it seems to work for them as they get to be paid for all iterations of a model printed.

They should indicate the actual REV. and DATE so there's no question.

Oh well, ordered. Thx again!

@kode54,

They should do a lot of things, but they don't. Many modellers, myself included have asked for a customizable variant field. We have been asking for over 5 years. They ignore almost all requests for site improvement. That is just one example of many.

Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓    Broad Selection ✓    Worldwide Delivery ✓

www.starbike.com

Nevertheless, you still provide a great service to the biking community. Thx for that.