The CAAD Build Thread...
Moderators: maxim809, Moderator Team
-
- Posts: 224
- Joined: Sat May 24, 2014 11:49 am
Don't post very often, but I do like my CAAD9
Full DA7900 except the chainset
About 7.4kg with the commuter / hubbardry / fred gear
About 7.0kg clean.
Full DA7900 except the chainset
About 7.4kg with the commuter / hubbardry / fred gear
About 7.0kg clean.
Scott Foil RC10 Ultegra 12 speed / Creston 50 - 7.9Kg
Frame: 2012 CAAD10 54cm
Wheelset: 2009 Campagnolo Eurus
Handlebar: Bontrager XXX Intergrated
Crankset: 2009 Campagnolo Chorus
Seat Post: Deda Superleggero
Saddle: Fizik Volta R1
Pedals: Speedplay Stainless
Shifters: Sram Force 10s
Front Derailer: Sram Red 10s
Rear Derailer: Sram Rival 10s
Brakes: Sram Rival 10s
Cassette: Sram Red 10s
Chainring: Sram 10s
Tires: Veloflex Corsa 23c
Finished in 6.9kg, custom painting for frame, Handlebar and seatpost.
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
Hi, I am a new CAAD user, just got CAAD12/2016/54cm. Just wondering if anybody has the same issue i have.
I am using shimano 5800 105 11spd and cant get satisfied with B tension properly.
If i make it strong enough to not rubbing chain with small/small cogs, shifting is not so good at outter ring+lower three rears. if i set to weak enough for large front, pully rubbs at lowest gear with small front.
I assume the reason is the RD cable housing. does anybody have a bright idea?
i was running 11/28+50/34
Tapatalk を使用して私の SOL26 から送信
I am using shimano 5800 105 11spd and cant get satisfied with B tension properly.
If i make it strong enough to not rubbing chain with small/small cogs, shifting is not so good at outter ring+lower three rears. if i set to weak enough for large front, pully rubbs at lowest gear with small front.
I assume the reason is the RD cable housing. does anybody have a bright idea?
i was running 11/28+50/34
Tapatalk を使用して私の SOL26 から送信
rukomasa wrote:Hi, I am a new CAAD user, just got CAAD12/2016/54cm. Just wondering if anybody has the same issue i have.
I am using shimano 5800 105 11spd and cant get satisfied with B tension properly.
If i make it strong enough to not rubbing chain with small/small cogs, shifting is not so good at outter ring+lower three rears. if i set to weak enough for large front, pully rubbs at lowest gear with small front.
I assume the reason is the RD cable housing. does anybody have a bright idea?
i was running 11/28+50/34
Tapatalk を使用して私の SOL26 から送信
in my opinion it appears to have a too short RD cable, compare it with that red caad12 posted above in this page
My 4,93 kg Supersix Evo HM: viewtopic.php?f=10&t=137647&start=30
My 6,22 kg Cannondale R500 1996: viewtopic.php?f=10&t=134364
My 6,22 kg Cannondale R500 1996: viewtopic.php?f=10&t=134364
-
- Posts: 1
- Joined: Mon Apr 17, 2017 8:29 pm
proud owner of CAAD12 Dura-ace Disc 2016.
I have one question I have been searching high and low for a carbon 0 set back seatpost (25.4mm) and cannot find anyone that makes one, does anyone know of a one off hand?
cheers
I have one question I have been searching high and low for a carbon 0 set back seatpost (25.4mm) and cannot find anyone that makes one, does anyone know of a one off hand?
cheers
angryfrank wrote:proud owner of CAAD12 Dura-ace Disc 2016.
I have one question I have been searching high and low for a carbon 0 set back seatpost (25.4mm) and cannot find anyone that makes one, does anyone know of a one off hand?
cheers
http://www.ebay.co.uk/itm/Hylix-Carbon- ... CzZl6RzJlg
Super light and work well, I have one on my caad12
Cannondale Systemsix Ultegra 2020
viewtopic.php?f=10&t=160844
viewtopic.php?f=10&t=160844
-
- Resident master of GIF
- Posts: 3405
- Joined: Mon Jul 18, 2011 2:44 am
- Contact:
looks great
-
- Posts: 14
- Joined: Fri May 19, 2017 4:43 am
- Location: Iowa City, IA
angryfrank wrote:proud owner of CAAD12 Dura-ace Disc 2016.
I have one question I have been searching high and low for a carbon 0 set back seatpost (25.4mm) and cannot find anyone that makes one, does anyone know of a one off hand?
cheers
I just picked up a Cannondale C2 25.4mm (350mm) 15 mm offset that is about 54 grams lighter than the stock C3 alloy seat post. The new seat post has plenty of room to chop off so I'm hoping to save another 80 grams or so. I paid $79.99 from Bicyclebuys.com
The new c2 post weighed 249.48 grams on my scale and the old C3 weighed 303.34
I do have a question though. The stem doesn't look carbon, but the packaging says it is. Does it just not look like "typical" carbon because it's Unidirectional carbon? I'd like to know for sure before I send it back or keep it and chop it.
Here is a link to a FSA zero offset 25.4mm http://www.outsideoutfitters.com/p-4389 ... oCEjrw_wcB that claims weight at 197 g for 350mm
Thanks in advance!
2017 Cannondale CAAD12
2005 Trek 7.4
Oldie Dahon Boardwalk
2005 Trek 7.4
Oldie Dahon Boardwalk
Posted in the cannondale thread but needs to be here too.
Caad12 58cm
Zipp 404 vittoria corsa 25c
Sram red 22 with bespoke chainrings
Deda zero100 bars and stem
Cannondale c2 carbon post
Pro stealth saddle
Carbonworks bidon cages.
Comes in at 7.12kgs.
Needs a lighter seatpost I reckon. Recommendations?
Caad12 58cm
Zipp 404 vittoria corsa 25c
Sram red 22 with bespoke chainrings
Deda zero100 bars and stem
Cannondale c2 carbon post
Pro stealth saddle
Carbonworks bidon cages.
Comes in at 7.12kgs.
Needs a lighter seatpost I reckon. Recommendations?
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com