Re: Anyone tried the Fulcrum RACING QUATTRO CARBON clincher
Posted: Sat Sep 08, 2018 1:08 pm
Have the Speed 40s and very pleased with them..
Sent from my SM-G935F using Tapatalk
Sent from my SM-G935F using Tapatalk
Weight Weenies
Forum
https://weightweenies.starbike.com/forum/
Anyone tried the Fulcrum RACING QUATTRO CARBON clincher
https://weightweenies.starbike.com/forum/viewtopic.php?f=3&t=137898
Page 8 of 8
Re: Anyone tried the Fulcrum RACING QUATTRO CARBON clincher
Posted: Sat Nov 03, 2018 10:54 am
Are the Stickers of the 2018 Version under the Coating or get it to removal?
Re: Anyone tried the Fulcrum RACING QUATTRO CARBON clincher
Posted: Sat Nov 03, 2018 10:54 am
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
Re: Anyone tried the Fulcrum RACING QUATTRO CARBON clincher
Posted: Tue Nov 20, 2018 4:14 am
I have had the Fulcrum Racing Quattro Carbon DB versions for about 11 months. I have had a couple of issues that I wonder if anyone else in the community has experienced:
1. After several visits to the LBS and the Fulcrum distributor, it seems impossible to remove a small amount of lateral side to side movement in the rear hub (it has been adjusted a number of times).
2. My LBS is just replacing the bearings on both wheels for the 2nd time this year (going with better quality this time). I have done around 7k kms so far this year. The LBS tells me the hubs are not sealed on the disc side which is allowing water into the bearings more readily. Not sure if this is common.
Anyone else experiencing either of these issues? Any ideas on solutions would be welcome.
1. After several visits to the LBS and the Fulcrum distributor, it seems impossible to remove a small amount of lateral side to side movement in the rear hub (it has been adjusted a number of times).
2. My LBS is just replacing the bearings on both wheels for the 2nd time this year (going with better quality this time). I have done around 7k kms so far this year. The LBS tells me the hubs are not sealed on the disc side which is allowing water into the bearings more readily. Not sure if this is common.
Anyone else experiencing either of these issues? Any ideas on solutions would be welcome.
Re: Anyone tried the Fulcrum RACING QUATTRO CARBON clincher
Posted: Wed May 22, 2019 1:23 pm
Just for anyone going through this process - use a hairdryer to heat the adhesive and it should come away with the decal. Follow the decal with the flow of hot air as you peel, and don't rush.pdlpsher1 wrote: ↑Mon Oct 02, 2017 4:44 pmI finished removing the stickers. There were twelve of them! I already have some acetone on hand so I used it. It worked well enough but it took three hours per wheel. The nude wheels definitely look awesome. Total weight without the stickers is 1,462g., which is one gram less than my Bora 50's. Today's a rainy day so I won't be trying them until tomorrow or Wednesday.
If I get a disc bike I would definitely go for the disk version of this wheelset.
Re: Anyone tried the Fulcrum RACING QUATTRO CARBON clincher
Posted: Thu May 23, 2019 3:07 am
Re: Anyone tried the Fulcrum RACING QUATTRO CARBON clincher
Posted: Sun Apr 25, 2021 1:57 pm
Has anyone set the Quattro DB up tubeless? What is it that prevents these from being tubeless? I read something about them missing a notch that holds the tyre on in case of a flat, but don't all the new hookless tubeless rims have that same issue? Surely keeping the pressure under 70psi is all that matters?
Re: Anyone tried the Fulcrum RACING QUATTRO CARBON clincher
Posted: Mon Apr 26, 2021 12:17 am
Which bearings did you go with?NCTales wrote: ↑Tue Nov 20, 2018 4:14 amI have had the Fulcrum Racing Quattro Carbon DB versions for about 11 months. I have had a couple of issues that I wonder if anyone else in the community has experienced:
1. After several visits to the LBS and the Fulcrum distributor, it seems impossible to remove a small amount of lateral side to side movement in the rear hub (it has been adjusted a number of times).
2. My LBS is just replacing the bearings on both wheels for the 2nd time this year (going with better quality this time). I have done around 7k kms so far this year. The LBS tells me the hubs are not sealed on the disc side which is allowing water into the bearings more readily. Not sure if this is common.
Anyone else experiencing either of these issues? Any ideas on solutions would be welcome.
Re: Anyone tried the Fulcrum RACING QUATTRO CARBON clincher
Posted: Wed Apr 28, 2021 6:38 pm
I had Fulcrum Quattro carbon rim brake during 2018 and 2019 season. Done lots of trips in Italian alps without problems.
Re: Anyone tried the Fulcrum RACING QUATTRO CARBON clincher
Posted: Thu Apr 29, 2021 9:34 am
I have Fulcrum Quattro carbon rim brake wheels for some years now. Great wheels without problems but I don't use them often because it is my backup wheelset.