Specialized Tarmac Pro SL6, 56 (2019) (Operation TransAlp)

Who are you (no off-topic talk please)

Moderator: Moderator Team

Jugi
Posts: 495
Joined: Sun Jun 24, 2018 8:10 am

by Jugi

Since completing the build,

Got a cheeky little christmas present. Definetly not weightweenie, but I'm not ashamed to admit watching a continous cycling commercial.
Image

Decided to get a pair of XLC Pro SL skewers. They feel a bit "soft" when tightening compared to heavier skewers. It remains to be seen how they perform in actual use.
Image

Built a set of wheels for the bike. Aimed at 1300 g and ended up at 1304 g, not too bad.
Image

Here she is:
Image

Modern rims (25mm wide at brake track and 27mm at widest point) compliment the frame and direct mount brakes.
Image

The old 3T Ergonova LTD doesn't suits the bike's color scheme very well, but I like the bar so much I don't want to change. I already experimented sanding down a 3T Doric LTD seatpost of similar age, which went quite well. Doesn't save a lot of weight, but transforms aesthetics. If inspiration strikes, I might remove the paint in the near future.
Image

Garmin Edge 1000 attached to F3 Cycling's Form mount.
Image

Image

Image

Weight (for now, at least) about 6,8 kg (without the Garmin). Spreadsheet updated respectively in the first post. Wonderful, I can still race without ballast!
Image

by Weenie



Jugi
Posts: 495
Joined: Sun Jun 24, 2018 8:10 am

by Jugi

Minor changes since last update (buildsheet at first post updated):

Changed saddle from Fizik Antares R1 to Arione R1. In a honeymoon phase right now. I (may) have finally found a suitable saddle, it took only eight years.

Changed handlebar from 3T Ergonova LTD 42cm to Ergonova Team Stealth 38cm, gained 7-9 g in the process. Also went from traditional to integrated brake cable routing. At first it seemed like the dreaded 3T cable integration wouldn't work at all, the brakes were slow to retract. I considered changing to PowerCordz cables which are more bendy than a traditional steel cable. However the setup seemed to take some bedding in and started to work just fine after a while.

Image

Felt like I could lower the cockpit even more, so got a Ceramic Speed dust cover for the headset. Lost a couple of grams and got the cockpit 3-4mm lower.

Image

Got the Hopp Carbon ICR port cover and lost a couple of grams.

Image

Image

After a long dreary winter, spring has finally come up knocking at the door. Went out on it yesterday and gave it some beans. Damn that was fun!

Image

gurk700
Posts: 251
Joined: Fri Jan 20, 2017 7:40 pm

by gurk700

Looking great... BUT!
If I'm honest, I loved your previous setup with the FFWD wheels :)

mvcap
Posts: 108
Joined: Fri Apr 22, 2016 9:50 pm

by mvcap

Which wheels are those you are currently running?

Jugi
Posts: 495
Joined: Sun Jun 24, 2018 8:10 am

by Jugi

Light Bicycle RRU45T02 rims (stealth decal and grooved brake track), Tune Mig70 front hub (20h), Syntace HiTorque RS rear hub (24h), Sapim CX-Ray spokes and Sapim DoubleSquare nipples. With Syntace hubs front and rear the set was at 1304g and with a Mig70 they should be about 1308g.

I have been thinking about relacing the rear to a Tune Mag170, but there wouldn't be much difference in spoke bracing angle or weight, I like the HiTorque's bearing preload adjustment more than Tune's shim system and I like the star ratchet freehub in HiTorque. So, the rear hub is like a lighter DT Swiss 240s with a preload adjustment and the front is just a light workhorse hub which hopefully resists all environmental effects a road bike might encounter.

mvcap
Posts: 108
Joined: Fri Apr 22, 2016 9:50 pm

by mvcap

Thanks!

User avatar
jbaillie
Posts: 561
Joined: Thu Nov 01, 2012 4:17 pm

by jbaillie

Another WW supernice
Image

wfcarrot
Posts: 43
Joined: Sat Feb 23, 2019 8:46 pm
Location: New York, US

by wfcarrot

I want the carbon port cover!! Perfect color match
2018 Sworks Tarmac SL6 - 7.2kg
2017 Colnago C60 - 6.29kg

User avatar
Rappid
Posts: 98
Joined: Thu Sep 11, 2008 1:24 pm
Location: Ireland
Contact:

by Rappid

Nice build!
I will be looking for that bike @TTA.
See you in Innsbruck! :)

Jugi
Posts: 495
Joined: Sun Jun 24, 2018 8:10 am

by Jugi

Final configuration for the Alps: 50/34 Q-rings, SRAM Red XG-1190 11-28 cassette and a SRAM Red 22 chain. Sitting at 6,74 kg.

Image

I've started to grow a bit weary of the aluminium link brake housing. I have been using this type of housings for years on multiple bikes. On some bikes they seem to stay silent no matter what use and abuse they'll end up going through. On some bikes they are just fine for a couple of months after initial install, but after a rainy ride or riding in particularly dusty conditions, on this frame they eventually started to creak. For this build, a problematic area seems to be rear brake cable housing's entry into the top tube. So far I've tried a couple of different things to remedy the creak, but haven't found a viable solution yet. As the bike is completely silent otherwise (not mentioning the hum of carbon and some healthy drivetrain noise), I may just end up switching to normal brake housing at some point.

Post Reply
  • Similar Topics
    Replies
    Views
    Last post