HOT: Active* forum members generally gain 5% discount at starbike.com store!
Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Articles FAQ Contact About




Post new topic Reply to topic  [ 10 posts ] 
Author Message
PostPosted: Fri Aug 31, 2012 8:58 pm 
Offline

Joined: Mon Apr 05, 2010 4:14 pm
Posts: 172
I made the mistake of opening one of my pd7810s because I was concerned it had got water in the bearings. It hadn't, but I had obviously dislodged something because now it will not close. It gets to within about half a mm on the threads compared to how it used to be adjusted, but not all the way. Correct number of bearings installed (17, 9 and the roller bearing) and it hasn't got too much grease in there whilst I figure out what is wrong. How should the bearing retainer on the larger race sit?

Anyone else serviced one of these or can point me towards a how to? The Park one just says don't do it!


Top
 Profile  
 
Posted: Fri Aug 31, 2012 8:58 pm 


Top
  
 
PostPosted: Fri Aug 31, 2012 11:05 pm 
Offline

Joined: Mon Apr 05, 2010 4:14 pm
Posts: 172
See photo below:
http://db.tt/LU9AgwOX


LH pedal is correctly adjusted, RH is not. The first gap between the spindle and the axle cone assembly is too small on the RH pedal, meaning that the axle cone assembly cannot close up snugly to the pedal body. The exploded view
http://techdocs.shimano.com/media/techdocs/content/cycle/EV/bikecomponents/PD/EV-PD-7810-2662_v1_m56577569830612675.pdf" onclick="window.open(this.href);return false;" onclick="window.open(this.href);return false;

does not shed any light on how I have managed to move the cone on the spindle, but it certainly didn't require a lot of force! Any help greatly appreciated.


Top
 Profile  
 
PostPosted: Fri Aug 31, 2012 11:59 pm 
Offline

Joined: Tue Aug 02, 2011 5:54 pm
Posts: 142
Coincidentally, I've been working on overhauling a set of PD-7810 pedals for the last two days.

I posted about it here:

http://forums.roadbikereview.com/compon ... 89166.html" onclick="window.open(this.href);return false;" onclick="window.open(this.href);return false;

My issue is play in the spindle (assembly). I think my problem may be related to the rubber sleeve (wear?) that sits between the spindle and cone piece, but I have yet to find a way to eliminate the play.

For your issue, can you not simply back off on the locknut? There should be a gap there.


Top
 Profile  
 
PostPosted: Sat Sep 01, 2012 4:20 am 
Offline

Joined: Mon Oct 15, 2007 9:28 pm
Posts: 897
Sorry to hear is. In my experience, opening a Shimano pedal is the kiss of death. Once opened- they will die in 6 months.
Shimano pedals usually last forever- but when you get a bad one it is all over.


Top
 Profile  
 
PostPosted: Sat Sep 01, 2012 11:25 am 
Offline

Joined: Mon Apr 05, 2010 4:14 pm
Posts: 172
Thanks guys! Yes, wish I had never touched them. The good side has been perfect from the day I bought them and is buttery smooth after thousands of wet kms. The bad side developed a tiny bit of play but I should never have touched it.

Sanrensho, how do you access the rubber sleeve/get the cone bit off the spindle? Take the circlip off? Yes I can tighten the locknut closer to the pedal body but not far enough, the cone assembly seems to be in the wrong place on the spindle by about a mm and I'm not sure how it got there. The first gap after the pedal thread stopper was about 1.5 mm and is now about half a mom.


Top
 Profile  
 
PostPosted: Sat Sep 01, 2012 3:38 pm 
Offline

Joined: Mon Oct 12, 2009 6:36 pm
Posts: 246
See the exploded view chart for the components: http://techdocs.shimano.com/media/techd ... 612675.pdf

The rubber seal should be 'underneath' the ball bearings, on the pedal thread side. Use something small and pointy between the bearings to push the seal down if they interfere with the bearings. If the seal sits correctly, the bearings should fall in to place and should be touching each other (there should not be any gap!) when you push the lock nut towards the circlip. If they do not fall into place while assembling, push the locknut up so the bearings sit in the right place while assembling.


Top
 Profile  
 
PostPosted: Sat Sep 01, 2012 8:23 pm 
Offline

Joined: Mon Apr 05, 2010 4:14 pm
Posts: 172
^^ daj, top man, thank you. I don't think the seal is seating properly as the bearings are not sitting together, I will try to push it back gently and then rebuild with fresh balls.


Top
 Profile  
 
PostPosted: Sun Sep 02, 2012 7:19 pm 
Offline

Joined: Tue Aug 02, 2011 5:54 pm
Posts: 142
daj wrote:
The rubber seal should be 'underneath' the ball bearings, on the pedal thread side. Use something small and pointy between the bearings to push the seal down if they interfere with the bearings. If the seal sits correctly, the bearings should fall in to place and should be touching each other (there should not be any gap!) when you push the lock nut towards the circlip. If they do not fall into place while assembling, push the locknut up so the bearings sit in the right place while assembling.


Thanks for this, daj. It sounds like the rubber seal needs to be sitting a certain way when the axle assembly is finally inserted into the body, but I'm having a hard time picturing this.

Do I need to position the rubber seal in the direction of the bearings, so that the seal and sliding part (cone) eliminate any play between the cone, bearings, and circlip? So it's a positioning/play adjustment that needs to be done right before reinserting the axle assembly into the body?

Thanks!


Top
 Profile  
 
PostPosted: Sun Nov 17, 2013 3:05 am 
Offline
Moderator
User avatar

Joined: Sat Mar 14, 2009 6:08 am
Posts: 7501
Location: Geeeelong! / YURP
So my left hand DA 9000 pedal seems to be 'leaking' grease

Image

only just noticed it. Which given my bike is washed every couple of rides, can only be within the last day or so.

Spinning the pedal it also feels 'rough'. Thoughts?

_________________
http://www.nicksquillari.com.au


Top
 Profile  
 
Posted: Sun Nov 17, 2013 3:05 am 


Top
  
 
PostPosted: Sun Nov 17, 2013 5:37 am 
Offline

Joined: Tue Nov 11, 2003 9:47 pm
Posts: 1637
Location: Santa Cruz, California, USA
If it feels rough it needs a rebuild. Probably including a new seal.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 10 posts ] 


Who is online

Users browsing this forum: ChristianB, Google Adsense [Bot], LAN, mike, rmerka, VamP and 67 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. Complaint about Tune's customer service

[ Go to page: 1, 2 ]

in Road

Frankie - B

18

1767

Thu Jan 09, 2014 8:40 pm

barsook77 View the latest post

There are no new unread posts for this topic. Zipp Service Course SL Bolt Change?

in Road

ToffieBoi

5

423

Thu Feb 20, 2014 5:32 am

mitchgixer6 View the latest post

There are no new unread posts for this topic. Zipp Service Course SL TB Bars, Reach as Published? 

in Road

tokyoturtle

1

515

Wed Aug 21, 2013 2:54 am

bricky21 View the latest post

There are no new unread posts for this topic. zipp sl carbon bars / service course sl alloy stem weighed

in Road

strobbekoen

4

949

Tue Dec 31, 2013 4:26 pm

mdeth1313 View the latest post

There are no new unread posts for this topic. Attachment(s) SRM mount - Where to get bearing piece?

in Road

shinkansen

3

208

Tue Jul 01, 2014 7:54 pm

shinkansen View the latest post


It is currently Tue Jul 29, 2014 3:47 pm

All times are UTC + 1 hour




Advertising   –  FAQ   –  Contact   –  Convert   –  About

© Weight Weenies 2000-2013
hosted by starbike.com


How to get rid of these ads? Just register!


Powered by phpBB