HOT: Active* forum members generally gain 5% discount at starbike.com store!
Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Articles FAQ Contact About




Post new topic Reply to topic  [ 7 posts ] 
Author Message
PostPosted: Wed Jun 05, 2013 5:02 am 
Offline

Joined: Fri Nov 09, 2012 4:57 am
Posts: 58
Hi there,

Have just built a new bike and have Planet X Ultralight brakes, the stopping power is fine and I really love them. Also as a note, using Yokozuna cables and housing, the housing being very stiff.

Have had them set up by a bike mechanic (i'm not one) and they worked fine for the first few rides.

I know this has been asked previously but I couldn't seem to find any examples where someone had the same problem as me.

Occasionally, after pulling on the brakes, one of the brake pads doesn't get pushed back far enough and the pad starts to rub on the rim.
This is not due to wheel flex etc. The first time it happened it was pressed so hard against the rim the wheel isn't able to spin.

I got the caliper tightened but the problem still exists, this time it seems that the brake pads rub a little, however is very noticeable.

One of my friends mentioned that he thought that housing might either be too short or too long.
Does anyone else who has used / installed these brakes have any input?
It's just frustrating as it's not every single time I use the brakes, only happens occasionally.


Top
 Profile  
 
PostPosted: Wed Jun 05, 2013 5:39 am 
Offline

Joined: Fri Apr 20, 2012 9:04 pm
Posts: 234
If you do a search there is a recent threat on this subject.


Top
 Profile  
 
Posted: Wed Jun 05, 2013 5:39 am 


Top
  
 
PostPosted: Wed Jun 05, 2013 7:05 am 
Offline

Joined: Fri Nov 09, 2012 4:57 am
Posts: 58
Like a bomb threat ;)?
Okay will do, I her performed searches for this issue, but couldn't find anyone that had the same problem as me.


Top
 Profile  
 
PostPosted: Wed Jun 05, 2013 1:01 pm 
Offline
User avatar

Joined: Fri Feb 11, 2011 3:04 am
Posts: 2369
Location: Mississippi
Adjust cable housing....if the housing is "pushing" the NDS pad into the rim, shorten the housing. If the housing is "pulling" the DS pad into the rim, cut a longer housing. Solved.

_________________
Cervelo R3

http://weightweenies.starbike.com/forum/viewtopic.php?f=10&t=125962


Top
 Profile  
 
PostPosted: Wed Jun 05, 2013 1:08 pm 
Offline

Joined: Fri Nov 09, 2012 4:57 am
Posts: 58
Thanks mate - I managed to find the other thread that beancounter was referencing to. Looks good :)


Top
 Profile  
 
PostPosted: Wed Jun 05, 2013 1:36 pm 
Offline
User avatar

Joined: Sat Aug 29, 2009 4:30 pm
Posts: 1530
If the brake fixing bolt is snug, it will resist forces that tend to de-center.
But if the cable housing is the wrong length, it will tend to push (or pull) it off center. So both should be checked for proper installation.


Top
 Profile  
 
Posted: Wed Jun 05, 2013 1:36 pm 


Top
  
 
PostPosted: Wed Jun 05, 2013 7:24 pm 
Offline

Joined: Fri Mar 26, 2010 4:24 pm
Posts: 91
Planet X brakes are single pivot brakes. Like all single pivot brakes, they rely on separate springs to retract each arm independently. Sometimes the springs do not exert the same force. Sometimes there are different amounts of friction on each arm. Sometimes the cable stiffness exerts unbalanced forces on the arms. Addressing any of these may help keep them centered.

Technical note:

Traditional single pivot brakes have lower mechanical advantage than either dual pivot brakes or leverage enhanced single pivot brakes (like the Planet X). The lower leverage allowed for larger pad-to-rim clearances, which in turn made these brakes less sensitive to variations in arm retraction forces.

Dual pivot brakes have additional linkages, which result in the arms retracting in unison. Once centered, the arms will always retract uniformly. (Due to the linkage, dual pivot brakes only require one spring to retract both arms.) The centering linakge allows dual pivot brakes to have higher leverage and lower pad-to-rim clearance, without the problem of pads dragging.

Leverage enhanced single pivot brakes can be lighter than dual pivot brakes, but the reduced pad-to-rim clearance makes them more sensitive to non-uniform arm retraction. These brakes must be set-up more carefully, paying closer attention to initial centering and cable length/stiffness, and are more prone to go out of centering adjustment in use. As they say, you can't get something for noting.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 


Who is online

Users browsing this forum: Bing [Bot], CGT, deek, djconnel, Google [Bot], Google Adsense [Bot], rbrtwyn and 51 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

   Similar Topics   Author   Replies   Views   Last post 
This topic is locked, you cannot edit posts or make further replies. planet x cnc ultra light brake calipers

in Road

KTCY

6

751

Fri Apr 04, 2014 9:08 am

trychle View the latest post

There are no new unread posts for this topic. Dura ace 7900 front brake installation issue

in Road

amey

4

227

Wed Sep 03, 2014 1:31 pm

amey View the latest post

There are no new unread posts for this topic. Attachment(s) 25mm tyre clearance issue with Ultegra 6800 rear brake

in Road

martinko

14

1409

Fri Sep 19, 2014 2:10 pm

ricks123 View the latest post

There are no new unread posts for this topic. Campy Record 11 FrontBrake centering

[ Go to page: 1, 2 ]

in Road

random101

15

615

Sat Sep 13, 2014 4:21 pm

bikewithnoname View the latest post

There are no new unread posts for this topic. Planet -X Saddles

in Road

moshinho

0

383

Sat Aug 02, 2014 1:17 pm

moshinho View the latest post


It is currently Fri Oct 24, 2014 6:23 pm

All times are UTC + 1 hour




Advertising   –  FAQ   –  Contact   –  Convert   –  About

© Weight Weenies 2000-2013
hosted by starbike.com


How to get rid of these ads? Just register!


Powered by phpBB