HOT: Active* forum members generally gain 5% discount at starbike.com store!
Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Blog NEW Articles FAQ Contact About




Post new topic Reply to topic  [ 13 posts ] 
Author Message
PostPosted: Tue May 14, 2013 7:36 pm 
Offline

Joined: Thu Apr 18, 2013 12:34 pm
Posts: 53
I'm in to process of building up a SuperSix Di2 frame and I'm wondering how much I should be worried about the internal wires being rubbed by the BB30 spindle. With the Shimano bottom brackets there is always a plastic sleeve, but I don't see how I can keep at lease one wire from rubbing the axle unless I hold it to the bottom of the frame with vinyl tape.

Am I just over thinking things? :noidea:


Top
 Profile  
 
Posted: Tue May 14, 2013 7:36 pm 


Top
  
 
PostPosted: Tue May 14, 2013 8:35 pm 
Offline

Joined: Tue Feb 05, 2013 8:29 pm
Posts: 236
You could use a small length of heat shrink or a drinking straw. It's not necessary though, there's no force pushing the wire against the spindle. It might wear through in 10,000 miles or so. Maybe. But you're probably switching parts and rewiring a little more often than that, right?


Top
 Profile  
 
PostPosted: Tue May 14, 2013 9:39 pm 
Offline

Joined: Sun Mar 27, 2011 8:16 pm
Posts: 433
I've got over a thousand miles on my SystemSix with a section of yoghurt pot used to hold the Di2 wire away from the rotating axle.

The wire runs in the hole that was previously used to locate the BB wire guide, is held against the inside of the shell by the section of pot, and then runs up the seat tube to the in-seat-post battery.


Top
 Profile  
 
PostPosted: Tue May 14, 2013 9:57 pm 
Offline

Joined: Fri Sep 30, 2011 4:48 pm
Posts: 48
DaleRider wrote:
I'm in to process of building up a SuperSix Di2 frame and I'm wondering how much I should be worried about the internal wires being rubbed by the BB30 spindle.

Agree that it's probably not a huge deal. Are you planning to use a Shimano crank? I recently built a supersix with a Sram PF30 bottom bracket, Sram crank and Di2 transmission. The SRAM BB had a sleeve:

Image

If you're going Shimano crank, consider the Praxis PF30/BB30->Shimano Hollotech adapter. It comes with a sleeve and the adapter design is quite smart:

http://praxiscycles.com/pages/conversion

Image


Top
 Profile  
 
PostPosted: Tue May 14, 2013 11:35 pm 
Offline

Joined: Thu Apr 18, 2013 12:34 pm
Posts: 53
@415brian I have the Praxis BB in my cross bike and I love it.

I'm going to be running an SiSl2 crank with Spidering gears for this build. I'm trying to save weight where possible. I've posted details in the build thread I've got in the Intro/Gallery section.


Top
 Profile  
 
PostPosted: Wed May 15, 2013 3:22 am 
Offline

Joined: Fri Sep 30, 2011 4:48 pm
Posts: 48
DaleRider wrote:
I'm going to be running an SiSl2 crank with Spidering gears for this build. I'm trying to save weight where possible.

Gotcha - sounds like you already have a (sleeveless) SiSl2 Cannondale PressFit Bottom Bracket. If you wanted to, could you run a (sleeved) Sram PF30 bottom bracket with the SiSl2 spindle and spacer bits? Now I'm just curious.

Of course, that's probably not worth the money. I'd probably just hide or tape the Di2 wires as best you can.

Your build is similar to mine and that's probably why I think it looks sharp.


Top
 Profile  
 
PostPosted: Wed May 15, 2013 12:37 pm 
Offline

Joined: Thu Apr 18, 2013 12:34 pm
Posts: 53
I think I'm going to go with a bit of this instead.

Image

Doesn't weigh much and should provide more than enough protection.


Top
 Profile  
 
PostPosted: Wed May 15, 2013 3:14 pm 
Offline

Joined: Fri Sep 30, 2011 4:48 pm
Posts: 48
DaleRider wrote:
I think I'm going to go with a bit of this instead.


good call!


Top
 Profile  
 
PostPosted: Thu May 16, 2013 4:35 pm 
Offline
Shop Owner
User avatar

Joined: Sun Feb 06, 2005 4:22 pm
Posts: 3561
Location: Tucson, Az.
I've done a few bikes like this and have taken PF30 bb's, removed the bearings and cut the cups down so that they fit inside the frame but left them large enough to have friction between the shoulder and the frame. That way they stay centered and have enough friction that they don't spin.

_________________
Fair Wheel Bikes

Fair Wheel Blog

Friend me on Facebook for behind the scenes updates


Top
 Profile  
 
PostPosted: Sat May 18, 2013 1:18 am 
Offline

Joined: Thu Feb 23, 2012 1:19 pm
Posts: 66
I just built up my Parlee Z1 with a PF30 bb with the Cannondale SISL2 Spiderring crankset and the Shimano DA 9079 DI2 drivetrain.

My builder used the Cannondale SL2 68x109 mm Ceramic bb part no. KP247 plus the PF30 shell from the Cannondale Pressfit BB30 PF30 bb shell part no. KP197 because we were concern qthat the DI2 wires might rub against the rotating axle if we used the Cannondale SL2 68x109 mm Pressfit Ceramic bb part no. KP248 that has a bearing PF shell/shield only. You can look up these parts at the www.cannondaleexperts.com site.

Or, you could use the SRAM Pressfit Ceramic BB30 Part no. 12XS267. That was what we used for my Lynskey Helix OS with a PF30 bb with the Cannondale Hollowgram SISL crankset with the SRAM Red drivetrain.

Mark

_________________
2012 Lynskey R330 with SRAM Red Quarq
2013 Parlee Z1 with DA 9070
2013 Lynskey Helix OS II with SRAM Red


Top
 Profile  
 
PostPosted: Sat May 18, 2013 7:04 am 
Offline

Joined: Mon Dec 31, 2012 5:27 am
Posts: 43
i have a similar concern. i intend to use square taper BB. Those that should have enough clearance to run the wire in between the BB and the shell are -

1) http://www.whiteind.com/bottom-brackets.html
2) http://www.specialites-ta.com/gb/boitier-axix-rte.html

Can anyone suggest others that can be used?


Top
 Profile  
 
PostPosted: Wed May 22, 2013 8:55 am 
Offline

Joined: Fri Sep 30, 2011 4:48 pm
Posts: 48
Here's another option...a simple rolled up piece of plastic. In this build, I'm using a Praxis BB30 adapter for Shimano Hollowtech cranks.

Photos below. The non-drive-side of the Praxis converter is installed, but not the drive side yet. First picture is the Di2 wires, second is the plastic shield, and the third is the shield installed. It's working surprisingly well. It's light, the wires are protected, and there's zero friction:

Image
Image
Image


Top
 Profile  
 
Posted: Wed May 22, 2013 8:55 am 


Top
  
 
PostPosted: Wed May 22, 2013 10:21 am 
Offline

Joined: Tue Apr 22, 2008 4:31 am
Posts: 149
That's clever, thanks 415brian.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 13 posts ] 


Who is online

Users browsing this forum: 06dhewett, cage, rbrtwyn, ryan0380 and 49 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. Help - Mavic R-SYS rear axle

in Road

Berk

12

1191

Sun Apr 13, 2014 1:06 pm

Berk View the latest post

There are no new unread posts for this topic. Freezing BB30 axle

[ Go to page: 1, 2 ]

in Road

ParisCarbon

17

1328

Thu Mar 13, 2014 6:33 pm

hmai18 View the latest post

There are no new unread posts for this topic. Cervelo R3 axle to crown lenght. 2014

in Road

Tmg57

4

746

Sun Dec 29, 2013 5:23 pm

Tmg57 View the latest post

There are no new unread posts for this topic. Out of stock - Internal Di2 Batteries

in Road

RexWrecks

8

751

Mon Mar 17, 2014 8:04 pm

carbonLORD View the latest post

There are no new unread posts for this topic. Cervelo S5 internal battery

in Road

cajer

8

732

Sat Aug 09, 2014 12:38 pm

rmerka View the latest post


It is currently Fri Dec 19, 2014 10:12 pm

All times are UTC + 1 hour




Advertising   –  FAQ   –  Contact   –  Convert   –  About

© Weight Weenies 2000-2013
hosted by starbike.com


How to get rid of these ads? Just register!


Powered by phpBB