Road shift cables with soldered ends
Moderator: robbosmans
For SRAM shifters its tough to get the cable through without it catching and unraveling. I've tried soldering it but no luck, whatever is on the cable interferes even with flux. So anyone know what brand of shft cable comes with the end pre soldered? I know I've seen them somewhere.
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
sungod wrote:there are both 1.2mm and 1.1mm gear cables, for sram i think 1.1mm is expected
if the end is neatly cut it should go through, you need to have the lever in the correct position too so that the cable has the easiest path
I agree it should go through but lots of people have the same issue
All new cables I've used have been soldered. I don't have issue getting them through. I used to think I had to take the that plate off but have since figured out how to get them trough without doing so.
New Red shifters are much easier to get cables through.
New Red shifters are much easier to get cables through.
tbh i've never had a problem (old sram red), but i used to do a *lot* of fine wiring!
rather than soldering, try a *small* drop of superglue on the very tip of the cable - too much will wick up the strands and stop it flexing - it'll be enough to stop strands separating, might be wise to degrease the tip first in case it's lubed
you can scrape any excess glue from the outside with a razor blade, so the diameter should be unchanged, unlike when applying solder
rather than soldering, try a *small* drop of superglue on the very tip of the cable - too much will wick up the strands and stop it flexing - it'll be enough to stop strands separating, might be wise to degrease the tip first in case it's lubed
you can scrape any excess glue from the outside with a razor blade, so the diameter should be unchanged, unlike when applying solder
-
- Shop Owner
- Posts: 1980
- Joined: Sat Jun 13, 2009 4:02 am
- Location: NoVA/DC
Ditto on the superglue method.
It's very hard to solder stainless cables. Cheap galvanized cables are easy, but I wouldnt use them for other reasons.
I have a feeling some of those "soldered" ends are welded, or at least heated much hotter.
It's very hard to solder stainless cables. Cheap galvanized cables are easy, but I wouldnt use them for other reasons.
I have a feeling some of those "soldered" ends are welded, or at least heated much hotter.
- spookyload
- Posts: 1048
- Joined: Wed Feb 23, 2005 6:47 am
- Location: Albuquerque, NM
I will pile on with the superglue method. The Superglue gel works the best. Just a small drop. Another method I have seen used is JB Weld. The benefit of that is you can sand the JB once it cures if it is too big.
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
basically every single end cable sold is "soldered".
The best solution for SRAM install is to pre bend the cable end a touch-wrap the end around a 5mm key to give it just a little curve at the tip. Install with the curve going "up and around the spool", goes in easy. Even works with cut cables if the cut was clean, Superglue if needed.
The best solution for SRAM install is to pre bend the cable end a touch-wrap the end around a 5mm key to give it just a little curve at the tip. Install with the curve going "up and around the spool", goes in easy. Even works with cut cables if the cut was clean, Superglue if needed.
after 2 drinks I'm a loser, after 3 a star