Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Blog NEW Galleries NEW FAQ Contact About Impressum
It is currently Thu Dec 08, 2016 5:21 pm
Recently the board software has been updated and there are some known bugs/failures:
- Avatars are currently not being displayed ✔ FIXED
- Tapatalk connection is currently broken ✔ FIXED
- Avatars cannot be uploaded ✔ FIXED

Please note that we will soon do some changes in WW board template design in case to get a fully mobile/desktop responsiveness board!
If you find more errors please post it here: http://weightweenies.starbike.com/forum/viewtopic.php?f=7&t=139062


All times are UTC+01:00





Post new topic  Reply to topic  [ 10 posts ] 
Author Message
PostPosted: Tue May 14, 2013 3:48 pm 
Offline

Joined: Mon Apr 19, 2010 10:33 pm
Posts: 167
For SRAM shifters its tough to get the cable through without it catching and unraveling. I've tried soldering it but no luck, whatever is on the cable interferes even with flux. So anyone know what brand of shft cable comes with the end pre soldered? I know I've seen them somewhere.


Top
   
Posted: Tue May 14, 2013 3:48 pm 


Top
   
 
PostPosted: Tue May 14, 2013 4:02 pm 
Offline

Joined: Fri Dec 24, 2010 9:37 pm
Posts: 956
Location: it's raining, it must be uk
there are both 1.2mm and 1.1mm gear cables, for sram i think 1.1mm is expected

if the end is neatly cut it should go through, you need to have the lever in the correct position too so that the cable has the easiest path


Top
   
PostPosted: Tue May 14, 2013 4:08 pm 
Offline

Joined: Mon Apr 19, 2010 10:33 pm
Posts: 167
sungod wrote:
there are both 1.2mm and 1.1mm gear cables, for sram i think 1.1mm is expected

if the end is neatly cut it should go through, you need to have the lever in the correct position too so that the cable has the easiest path


I agree it should go through but lots of people have the same issue


Top
   
PostPosted: Tue May 14, 2013 4:56 pm 
Offline

Joined: Tue Jun 08, 2010 4:58 am
Posts: 258
Location: Chicago
All new cables I've used have been soldered. I don't have issue getting them through. I used to think I had to take the that plate off but have since figured out how to get them trough without doing so.

New Red shifters are much easier to get cables through.


Top
   
PostPosted: Tue May 14, 2013 5:51 pm 
Offline

Joined: Fri Dec 24, 2010 9:37 pm
Posts: 956
Location: it's raining, it must be uk
tbh i've never had a problem (old sram red), but i used to do a *lot* of fine wiring!

rather than soldering, try a *small* drop of superglue on the very tip of the cable - too much will wick up the strands and stop it flexing - it'll be enough to stop strands separating, might be wise to degrease the tip first in case it's lubed

you can scrape any excess glue from the outside with a razor blade, so the diameter should be unchanged, unlike when applying solder


Top
   
PostPosted: Tue May 14, 2013 9:58 pm 
Offline
Shop Owner

Joined: Sat Jun 13, 2009 4:02 am
Posts: 1980
Location: NoVA/DC
Ditto on the superglue method.
It's very hard to solder stainless cables. Cheap galvanized cables are easy, but I wouldnt use them for other reasons.
I have a feeling some of those "soldered" ends are welded, or at least heated much hotter.


Top
   
PostPosted: Wed May 15, 2013 2:27 am 
Offline

Joined: Thu Sep 30, 2010 5:50 am
Posts: 315
They don't solder or weld the ends. In manufacturing they use arc cutting do it fuses the ends when cut to prevent unraveling.


Top
   
PostPosted: Wed May 15, 2013 5:39 am 
Offline

Joined: Thu Jul 12, 2012 10:47 am
Posts: 38
I've found that filing the end of the cable so that its smooth and blunt with no sharp points helps with feeding the cables through. Otherwise to answer your question, Jagwire cables have "soldered" ends.


Top
   
PostPosted: Wed May 15, 2013 5:53 am 
Offline
User avatar

Joined: Wed Feb 23, 2005 6:47 am
Posts: 958
Location: Albuquerque, NM
I will pile on with the superglue method. The Superglue gel works the best. Just a small drop. Another method I have seen used is JB Weld. The benefit of that is you can sand the JB once it cures if it is too big.


Top
   
PostPosted: Wed May 15, 2013 5:11 pm 
Offline

Joined: Sun Feb 25, 2007 5:05 pm
Posts: 83
Location: Netherlands
basically every single end cable sold is "soldered".

The best solution for SRAM install is to pre bend the cable end a touch-wrap the end around a 5mm key to give it just a little curve at the tip. Install with the curve going "up and around the spool", goes in easy. Even works with cut cables if the cut was clean, Superglue if needed.

_________________
after 2 drinks I'm a loser, after 3 a star


Top
   
Posted: Wed May 15, 2013 5:11 pm 


Top
   
 
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 10 posts ] 

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. 34/52T Campagnolo shift quality?

in Road

RedRacer

6

627

Tue Sep 06, 2016 5:51 am

Kurets View the latest post

There are no new unread posts for this topic. Di2 shift button blues

in Road

pdlpsher1

9

704

Wed Feb 17, 2016 11:27 am

Jason74 View the latest post

There are no new unread posts for this topic. do you guys keep your shift inner liners in the frame

[ Go to page: 1 2 ]

in Road

Delorre

15

1417

Mon Feb 15, 2016 4:08 am

BikeAnon View the latest post

There are no new unread posts for this topic. Electronic front shift question

in Road

mbrider

6

420

Wed Jun 01, 2016 2:40 am

2lo8 View the latest post

There are no new unread posts for this topic. brake and shift cable kits

in Road

toastie

4

725

Thu Dec 31, 2015 8:09 am

kkibbler View the latest post


All times are UTC+01:00


Who is online

Users browsing this forum: Bing [Bot], CLEAR, Google [Bot], hilts and 30 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited