Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Blog NEW Galleries NEW FAQ Contact About Impressum
It is currently Fri Dec 15, 2017 3:52 am

All times are UTC+01:00





Post new topic  Reply to topic  [ 8 posts ] 
Author Message
PostPosted: Fri Apr 26, 2013 5:23 am 
Offline

Joined: Mon Nov 05, 2007 12:38 am
Posts: 52
I bought a used CAAD10 frame and the bottom bracket seals were missing, presumably they fell off or stayed attached to the crank. Can I still use the bottom bracket? If not, I'll buy a new one and I have another question: I have a sram red quarq, do I need to use the sram bb or will any brand do?


Top
   
Posted: Fri Apr 26, 2013 5:23 am 


Top
   
 
PostPosted: Fri Apr 26, 2013 6:57 am 
Offline

Joined: Wed Jul 08, 2009 9:19 pm
Posts: 576
No. Buy a new bottom bracket. They are cheap.


Top
   
PostPosted: Fri Apr 26, 2013 8:16 am 
Offline
User avatar

Joined: Fri May 12, 2006 2:11 pm
Posts: 1366
Location: Stockholm, Sweden
Get a new bottom bracket I say too. Every BB30 is the same so brand doesn't matter.

_________________
/jonas l
http://cerrol.wordpress.com (my cyclingblog)


Top
   
PostPosted: Fri Apr 26, 2013 8:40 am 
Offline
User avatar

Joined: Tue Aug 08, 2006 1:41 pm
Posts: 853
Location: The Netherlands
The seals are not necessary, they just prevent dirt from getting into the bearings. So you should be able to use them.

_________________
My Renovo R1 wooden bike project and the reason for my passion for all that is wood.

Check it out: the most amazing vintage Colnago, Merckx and Pinarello collection


Top
   
PostPosted: Fri Apr 26, 2013 9:30 am 
Offline

Joined: Fri Dec 24, 2010 9:37 pm
Posts: 1360
Location: it's raining, it must be uk
you can run without seals, but...

if you ride in wet weather, or dusty/dirty conditions, you will need to reduce time between servicing, strip, clean, regrease, or bearing life will be reduced

my experience is that not all bearings sold for bb30 are equal, i've had a set that were very slack on the axle, this caused fretting within just an hour, took them off, won't use them again

i never has this problem with sram branded bearings


Top
   
PostPosted: Fri Apr 26, 2013 11:44 am 
Offline

Joined: Thu Mar 26, 2009 11:06 pm
Posts: 442
Location: Yorkshire - God's Own Country
Stick some tape over the ends! :D


Top
   
PostPosted: Fri Apr 26, 2013 2:48 pm 
Offline

Joined: Tue Nov 11, 2003 9:47 pm
Posts: 2196
Location: Santa Cruz, California, USA
If the seals on the bearings themselves are missing you need new bearings. But it's probably the secondary external seals that are missing. Those are less important. Unless you're riding off road or in the rain a lot you don't need them.

Few people regrease sealed bicycle bearings. Getting the seal off and back on without damaging it is a bit tricky on these small bearings with narrow seals. It's much easier on larger bearings with larger balls and thus larger seals.


Top
   
Posted: Fri Apr 26, 2013 2:48 pm 


Top
   
 
PostPosted: Fri Apr 26, 2013 10:45 pm 
Offline
Shop Owner

Joined: Sat Jun 13, 2009 4:02 am
Posts: 1980
Location: NoVA/DC
The "seals", the bearing shields, are necessary in the sense that you need them to space the crank properly. You can also use some other method to keep it spaced.
Bike shops can sell you just the shields. If the bearings are at all questionable, just replace them.
as far as fretting, I've found that that is most often caused not by tight or loose fit, but by bearing misalignment. FSA makes a bearing alignment checker for bb30 that I wish was more available. the fretting is usually accompanied by marks on the spindle that are sinusoidal, indicating that the bearing is crooked.
Just my 2cents


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 8 posts ] 

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. Bottom bracket bearings - removing seals and lube

in Road

kavitator

9

674

Thu Jul 13, 2017 1:27 am

Patto View the latest post

There are no new unread posts for this topic. BB30 circlips when fitting BB30-24mm Bottom Bracket

in Road

thepainandsuffering

2

290

Mon Oct 16, 2017 1:26 pm

hambini View the latest post

There are no new unread posts for this topic. Help me fix my CREAKING bb30 bottom bracket

[ Go to page: 1 2 3 ]

in Road

jobvisser

33

2825

Wed Apr 05, 2017 2:11 am

glepore View the latest post

There are no new unread posts for this topic. What bottom bracket do I need

in Road

JScycle

3

337

Tue Oct 31, 2017 7:56 am

JScycle View the latest post

There are no new unread posts for this topic. Bottom Bracket Drag

in Road

Ltoddokc

10

1482

Wed Oct 18, 2017 12:32 am

youngs_modulus View the latest post


All times are UTC+01:00


Who is online

Users browsing this forum: Bing [Bot], evan326, mnmasotto, toshi, Yahoo [Bot] and 17 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited