Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Blog NEW Galleries NEW FAQ Contact About
It is currently Fri Aug 26, 2016 2:43 am
Recently the board software has been updated and there are some known bugs/failures:
- Avatars are currently not being displayed ✔ FIXED
- Tapatalk connection is currently broken ✔ FIXED
- Avatars cannot be uploaded ✔ FIXED

Please note that we will soon do some changes in WW board template design in case to get a fully mobile/desktop responsiveness board!
If you find more errors please post it here: http://weightweenies.starbike.com/forum/viewtopic.php?f=7&t=139062


All times are UTC+01:00





Post new topic  Reply to topic  [ 38 posts ]  Go to page Previous 1 2 3
Author Message
PostPosted: Tue Apr 09, 2013 9:56 pm 
Offline

Joined: Wed Aug 11, 2010 7:52 am
Posts: 70
Hard to say what happened. If it is a bearing or the spindle, then it is an easy/cheap fix.

Just take it apart carefully and see whats wrong. Sorry to hear about it and good luck on getting it back together.


Top
   
PostPosted: Tue Apr 09, 2013 10:12 pm 
Offline
User avatar

Joined: Sun Dec 12, 2004 2:49 pm
Posts: 844
Location: Mårslet, Denmark
Did you remove the shoulder on the spindle? Is that why you have that carbon spacer on? The blank metal on the outside what is that?

_________________
It's online again:The Machinist

My CAAD10:http://weightweenies.starbike.com/forum/viewtopic.php?f=10&t=109014


Top
   
PostPosted: Fri Apr 12, 2013 1:26 am 
Offline

Joined: Mon Oct 24, 2011 5:13 am
Posts: 93
Please tell us what you've done in regards to your unorthodox hollowgram installation.


Top
   
PostPosted: Fri Apr 12, 2013 1:51 am 
Offline
Shop Owner

Joined: Sat Jun 13, 2009 4:02 am
Posts: 1980
Location: NoVA/DC
@Anders,
The spindles no longer have shoulders. Looks like a swap to a carbon spacer. Something funny going on with the dust shield, hard to say. I'm gonna go out on a limb and say it is related to using a whole lotta preload.

Edit: didn't realise it's the older arms. What spindle is that? And your tire is on backwards... ;-)


Last edited by thisisatest on Fri Apr 12, 2013 3:50 am, edited 1 time in total.

Top
   
PostPosted: Fri Apr 12, 2013 3:39 am 
Offline

Joined: Wed Apr 03, 2013 5:09 pm
Posts: 37
Location: AZ, USA
Ouch! Please tell us more once you find out.


Top
   
PostPosted: Fri Apr 12, 2013 10:24 am 
Offline
User avatar

Joined: Sun Dec 21, 2003 8:32 pm
Posts: 1467
Location: WALES,UK
Whats that carbon spacer doing on the inside of the arm?

_________________
Ti or dye!

The Weenie formally known as CAADHEAD


Top
   
PostPosted: Fri Apr 12, 2013 12:00 pm 
Offline

Joined: Sun Aug 29, 2010 12:30 pm
Posts: 48
Location: Denmark
Buffalo: I didn't install it, so hard for me to say.

Didn't realise that it was a mess to use a carbon spacer before now. Seems like i'm not the only one (http://www.cyclingnews.com/features/pho ... p-1/213655), but oh well that doesn't make it more right i guess.

The cranks will be disassembled later today and i will order new spare parts. Hopefully some new bearings, dustshield and aluminium spacer is all i need..


Top
   
PostPosted: Fri Apr 12, 2013 1:11 pm 
Offline

Joined: Sat Dec 13, 2003 2:25 am
Posts: 4743
Location: Canada
I think that the carbon spacer is causing some miscommunication. I don't think the other posters are questioning the carbon, I believe that they are questioning the use of a spacer at all.

On the older Si SL cranks (i.e., not the Si SL2 crank), I recall that there is no non-drive side spacer. The photo you have linked to is an MTB crank. I think we are assuming that you are running a road spindle. If you were running a MTB triple onna 132mm spindle, then you do need a 12mm spacer on the non-drive side, and a carbon one should be fine. With a road spindle, the spacer will side load the bearing. The Si SL2 crank and spindle set-up is different and does use a non-drive side spacer, I believe.

To be more clear, the road version of the Si Sl2 crank will have a wave washer, two or three shims and one of two different sizes of spacer on the non-drive side, depending upon the bottom bracket used.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 38 posts ]  Go to page Previous 1 2 3

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. Cannondale CAAD10 NDS BB wavy washer showing?

in Road

justkeepedaling

5

245

Wed Apr 20, 2016 4:25 am

jwfinesse View the latest post

There are no new unread posts for this topic. Cannondale CAAD10 drives use chainstay dented

in Road

DesmondOng

2

441

Sun Jan 31, 2016 11:38 am

Pottsy View the latest post

There are no new unread posts for this topic. 2011 Cannondale CAAD10 9000 x Zipp x Mavic CCU 6.579kg

in Introduce Yourself / Gallery - Please use metric weights.

riceboy

14

1946

Wed Oct 21, 2015 2:14 am

riceboy View the latest post

There are no new unread posts for this topic. 2015 CAAD10 frame parts

in Road

peterturbide

10

754

Tue Mar 15, 2016 1:16 pm

peterturbide View the latest post

There are no new unread posts for this topic. CAAD10 50CM Frame/fork Weight

in Introduce Yourself / Gallery - Please use metric weights.

JohnnieFranks

1

711

Thu Oct 01, 2015 3:52 pm

wheelzqc View the latest post


All times are UTC+01:00


Who is online

Users browsing this forum: duke249, jrobart, PFrides and 25 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited