HOT: Active* forum members generally gain 5% discount at starbike.com store!
Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Articles FAQ Contact About




Post new topic Reply to topic  [ 11 posts ] 
Author Message
PostPosted: Sat Apr 06, 2013 7:56 pm 
Offline
User avatar

Joined: Sun Feb 22, 2009 9:53 pm
Posts: 867
righty, got me a pair of these brakes the other day. In terms of centering them, what is the best technique? Being a young chap haven't had much experience with single pivot brakes and so these look a little confusing - any tips would be appreciated, seen a loads of these on bikes around here.

:mrgreen:


Top
 Profile  
 
PostPosted: Sat Apr 06, 2013 9:28 pm 
Offline

Joined: Thu Sep 29, 2011 7:20 am
Posts: 76
Not sure this will be a lot of help, but what I found out when I installed mine was that the cable housing routing and LENGTH had to be spot on so that the caliper would stay centered after squeezing the levers. To me that made the biggest difference than anything else. The rear caliper seems to be not as sensitive as the front to this, at least on my frame.

My 2 cents.


Top
 Profile  
 
Posted: Sat Apr 06, 2013 9:28 pm 


Top
  
 
PostPosted: Sat Apr 06, 2013 9:40 pm 
Offline
User avatar

Joined: Sat Aug 29, 2009 4:30 pm
Posts: 1530
My method:
1. Install into approximate position with mounting bolt slightly loose.
2. Adjust cable tension to give proper total rim clearance.
3. Squeeze the calipers down onto the rim with one hand and tighten the mounting bolt so the calipers are fixed at that "centered" position. Tighten to full final torque. You don't want them moving from here.
4. With calipers relaxed, check symmetry of centering and make final fine adjustments with the tiny set screw on the caliper arm.

I don't like to have my brakes ride really close to the rims anyway, so I can usually pull a 23mm clincher out without even loosening the brake cable. When I change wheels, the centering usually remains good enough that I don't have to readjust, or can get by with a small adjustment to the set screw.


Last edited by Rick on Sat Apr 06, 2013 9:42 pm, edited 1 time in total.

Top
 Profile  
 
PostPosted: Sat Apr 06, 2013 9:41 pm 
Offline

Joined: Fri Mar 16, 2012 1:49 pm
Posts: 136
Location: LA/OC, California
I found that adjusting them and keeping them centered was fairly simple. There's two 2mm screws in the center bolt. I loosened those, and used a 4mm to turn the whole brake in the direction that I wanted, and locked the two small bolts.

Haven't had an issue with centering yet, and my front brake housing is definitely too long. If the brakes get knocked out of center, a quick pull of the brake lever re-centers everything.

_________________
Bike: Felt FC

Strava


Top
 Profile  
 
PostPosted: Sat Apr 06, 2013 9:54 pm 
Offline

Joined: Mon Sep 17, 2012 10:53 pm
Posts: 478
Hmmmm I have to recenter mine after every ride. furstrating. And I had Planet X install mine for me and i still have issues.


Top
 Profile  
 
PostPosted: Sat Apr 06, 2013 11:25 pm 
Offline

Joined: Fri Apr 20, 2012 9:04 pm
Posts: 233
I'm with rick; don't have problems with mine.

One suggestion would be to leave yourself a bit of slack on the cable and tension up with the adjuster.

If you run your pads close to the rim it will allow you to get enough movement on the cable to pull the barrel from the arm (which will release the caliper arms) and slide your wheel out.

The other thing I have noticed is that I'd ever I mess around with them (eg taking wheel off) the little centering screw needs to be tweaked. I tend to loosen mine off as far as possible, squeeze the brake levers a couple of times, and them adjust until they are centred.

Not sure if that makes much sense!!!


Top
 Profile  
 
PostPosted: Sun Apr 07, 2013 12:12 am 
Offline
User avatar

Joined: Sun Feb 22, 2009 9:53 pm
Posts: 867
thanks guys !


Top
 Profile  
 
PostPosted: Sun Apr 07, 2013 7:09 am 
Offline

Joined: Wed Jun 27, 2012 12:22 am
Posts: 35
I like to think that I am for the most part pretty competent at working on my own bike and usually feel like I actually do a better job working on my own bike than most bike shop mechanics just because I am willing to spend lot of my own time to get things JUST right. That being said, I was pretty frustrated with setting up my Planet X brakes and couldn't get them really well centered despite spending quite a bit of time on them (there is some weird brake arm travel asymmetry on these when you use the fine adjustment screw on the caliper arm to extremes). Then I met some Planet X people at a bike show and they showed me a method to help centering that I haven't noticed mentioned online (or at least didn't understand).

RIck's method above is pretty spot on, but in between steps 3 and 4 you can take a 13mm spanner wrench and rotate the entire brake assembly around the main fixing bolt as I tried to show in my crappy picture below. Using this I am now able to set up the brakes so that each pad is equi-distant from the rim without braking, and then each pad contacts the rim at the same time during brake lever pull-ie properly centered. The performance of these brakes seems pretty great so far.

On a side note-the brakes have a somewhat interesting design feature that I'm not sure is intentional. No matter how poorly centered I had the brakes, they never really seem to push the rim off center under actually braking loads. Seems to me that upon contacting the rim, the arms are essentially self centering under load.

Image


Top
 Profile  
 
PostPosted: Mon Apr 08, 2013 12:20 am 
Offline

Joined: Thu Feb 24, 2011 6:33 pm
Posts: 285
Location: California
I've found a way to get these brakes centered nearly perfectly when installing (similar to what juanacity did with the spanner wrench and system787 did with the 2mm screws), except my method just requires a 4mm hex wrench - the trick is to loosen the mounting bolt, then use the 4mm wrench to hold the brake centered in place at the Ti center bolt while at the same time tightening down the brake mount bolt (preferably with a ratchet type wrench). As the brake mount bolt gets tighter, the turning force might move the brake a bit if you're not holding the 4mm wrench in place tight enough, but you just have to use the 4mm to re-center the brake and keep tightening the mounting bolt until it's secure.

If you did it right little to no adjustment of the side spring tension bolt is needed.

:beerchug:

_________________
strava / instagram


Top
 Profile  
 
PostPosted: Mon Apr 08, 2013 8:39 pm 
Offline
Formerly known as PezTech
User avatar

Joined: Tue Sep 26, 2006 12:37 am
Posts: 5699
Location: Phoenix Arizona
5 minute set up and zero cable length concern (but that might be different with different cables).

Zero issues in use.

_________________
charles@pezcyclingnews.com


Top
 Profile  
 
Posted: Mon Apr 08, 2013 8:39 pm 


Top
  
 
PostPosted: Mon Apr 08, 2013 9:18 pm 
Offline

Joined: Tue Dec 28, 2010 5:56 pm
Posts: 17
One thing that helped me get them dialed in was to squeeze the brake levers a couple times and re-adjust. I don't know if it's stress-relieving the bolts, or the spring, but it took a couple go's to get them to return to center correctly.

After a couple rides, they've been good so far. A little grabbier than 7800, but no lack of power.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 11 posts ] 


Who is online

Users browsing this forum: Bing [Bot], chiumomo, raisinberry777, sodac, stormur and 36 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. Installing fsa slk chainset

in Road

tinchy

2

205

Sat Jul 12, 2014 11:15 pm

tinchy View the latest post

There are no new unread posts for this topic. Installing 6870 Di2 Issue

in Road

Carrots

5

630

Wed Jun 04, 2014 8:43 pm

tnc1970 View the latest post

There are no new unread posts for this topic. Installing Recon Cassette

in Road

drainyoo

7

549

Sun Mar 09, 2014 3:49 am

drainyoo View the latest post

There are no new unread posts for this topic. Installing BB30 BB with SRAM Red Exogram

in Road

drainyoo

4

368

Sun Jun 08, 2014 7:22 am

grover View the latest post

There are no new unread posts for this topic. ultralight pannier bag help.

in Road

voodoojar

0

303

Sun Nov 10, 2013 7:41 pm

voodoojar View the latest post


It is currently Thu Oct 23, 2014 6:55 am

All times are UTC + 1 hour




Advertising   –  FAQ   –  Contact   –  Convert   –  About

© Weight Weenies 2000-2013
hosted by starbike.com


How to get rid of these ads? Just register!


Powered by phpBB