HOT: Active* forum members generally gain 5% discount at starbike.com store!
Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Articles FAQ Contact About




Post new topic Reply to topic  [ 8 posts ] 
Author Message
PostPosted: Wed Apr 03, 2013 7:38 pm 
Offline

Joined: Mon Mar 12, 2012 4:43 pm
Posts: 222
All,

I have an annoying problem. My commuting wheels are OP/DA 7900 hubs but my race wheels are carbon tubular/SL211 SuperLight rear hub. The annoying problem is the inability to simply change wheels and go; I have am forced to adjust my RD, which usually ends up with me mucking it. I have studied, much to no good, the specs for both hubs in a hope of deducing a method off installing the cassette on the BHS hub such this the cassette is in line with the DA7900 free hub.

Question 1: am I on the right track in that I could insert a spacer behind the cassette on the BHS hub in order to push it out and in line with the DA7900 hub?
Question 2: referencing "freespoke" (and/or other sources) and the BHS site, what spacer width would I use?
Question 3: any other alternatives beyond electric trimming and me becoming more proficient (mainly b/c my pit wheels are my OP/DA7900 wheels)


Top
 Profile  
 
PostPosted: Wed Apr 03, 2013 8:32 pm 
Offline

Joined: Tue Nov 11, 2003 9:47 pm
Posts: 1450
Location: Santa Cruz, California, USA
I've used a 1mm Shimano spacer on my SL211 hubs (with Sram cassettes, which normally don't use a spacer). That puts the cassette in line with my race wheels, which have White Ind hubs.

I have not twisted the 11t cog off yet but I don't make a lot of power.

It makes me wonder if a Shimano 11sp cassette would work on 10sp SL211 hubs, as they're only 1.85mm wider.


Top
 Profile  
 
Posted: Wed Apr 03, 2013 8:32 pm 


Top
  
 
PostPosted: Wed Apr 03, 2013 8:37 pm 
Offline

Joined: Mon Mar 12, 2012 4:43 pm
Posts: 222
Hi Eric,

I will try a 1mm spacer and see where that gets me. Also, I had been pondering the same question that you raised regarding 11-speed. Perhaps here will be able to test it.


Top
 Profile  
 
PostPosted: Fri Apr 19, 2013 3:25 am 
Offline

Joined: Mon Mar 12, 2012 4:43 pm
Posts: 222
A quick follow up before I try adding an additional 1mm spacer, do I run the risk of snapping the cassette off the hub? I rarely use the 11t cog. Also when experimenting with both spacers, the end of the cassette looks almost identical to the DA setup and feels secure without the lock ring. I feel that a Mavic spacer would be a perfect match, 1.85mm spacer


Top
 Profile  
 
PostPosted: Fri Apr 19, 2013 6:32 am 
Offline

Joined: Tue Jun 07, 2011 4:28 am
Posts: 112
Location: Berkeley, CA
Eric, I too run a 1mm spacer behind a Red cassette on the SL211 hub. However, I can tell you that an 11 Shimano cassette will not fit on the SL211 freehub. I thought it might, so I gave it a try last night, but the 11t cog will not catch the splines of the freehub at all. BHS now has an 11 speed Shimano hub, but no 11 speed conversion freehubs.


Top
 Profile  
 
PostPosted: Fri Apr 19, 2013 1:47 pm 
Offline

Joined: Fri Nov 18, 2011 5:13 am
Posts: 37
@headwind:
I would leave your cassette spacers alone if things have been working properly. The reason for discrepancy in rear shifting is different distances between the high cassette cog (small) and your drive side outer locknut or end cap. I've solved this problem by adding drive side spacers or filing down a locknut to a narrower width. Try measuring with a caliper the distance from dropout to 11t on both hubs with the wheel on the bike. Correct spacing as necessary until these distances are equal.


Top
 Profile  
 
PostPosted: Fri Apr 19, 2013 2:30 pm 
Offline

Joined: Mon Mar 12, 2012 4:43 pm
Posts: 222
@captainclarko - for clarification, the shifting is fine specific to each hub. The issue is switching between wheels/hubs. With two 1mm spacers behind the cassette on the SL211 hub, the chain line matches up 95% and requires zero RD adjustment. The 11t feels secure on the hub groove too. I am able to secure the lock ring.

I understand what you are suggesting. Alternatively I would like to place an additional hub washer behind the free body, but I cannot seem to be able to remove it. I am two 5mm metric wrenches, but I can only remove the NDS side. I must be overlooking something. I wish Brandon had a tech section on his site.


Top
 Profile  
 
PostPosted: Fri Apr 19, 2013 9:59 pm 
Offline

Joined: Tue Nov 11, 2003 9:47 pm
Posts: 1450
Location: Santa Cruz, California, USA
Wookieopolis- thanks for trying that and reporting back.


Top
 Profile  
 
Posted: Fri Apr 19, 2013 9:59 pm 


Top
  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 8 posts ] 


Who is online

Users browsing this forum: Google Adsense [Bot], jenfromzen, pdlpsher1, Yahoo [Bot] and 77 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. Tune 130 rear hub

in Road

SWijland

7

561

Tue Oct 15, 2013 4:55 pm

jmartpr View the latest post

There are no new unread posts for this topic. DI2 vs Rear Derailleur Hangers

[ Go to page: 1, 2, 3 ]

in Road

DaleRider

34

3400

Wed Feb 12, 2014 2:36 pm

DaleRider View the latest post

There are no new unread posts for this topic. Possible to fix this Sram Red rear derailleur?

in Road

micky

2

723

Sun Aug 11, 2013 9:24 pm

micky View the latest post

There are no new unread posts for this topic. Help - Mavic R-SYS rear axle

in Road

Berk

12

709

Sun Apr 13, 2014 1:06 pm

Berk View the latest post

There are no new unread posts for this topic. Zipp 202 rear hub spacers

in Road

paradawt

14

1043

Sat Jun 08, 2013 11:08 am

paradawt View the latest post


It is currently Thu Apr 24, 2014 4:10 pm

All times are UTC + 1 hour




Advertising   –  FAQ   –  Contact   –  Convert   –  About

© Weight Weenies 2000-2013
hosted by starbike.com


How to get rid of these ads? Just register!


Powered by phpBB