Stoked! Exp001 - 5671g/12.47lb
Moderators: MrCurrieinahurry, maxim809, Moderator Team
Really great bike, which I am certainly taking inspiration from. One thing I was wondering about was the omni seat post. I have found them on ebay, I was just wondering how you went about removing the logos, did you completely remove the lacquer and if so what did you refinish the post with?
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
- prendrefeu
- Posts: 8580
- Joined: Wed Oct 31, 2007 10:32 pm
- Location: Glendale / Los Angeles, California
- Contact:
Thanks!
Logos were sanded off with 400grit sand paper, and they went rather quickly. Then followed with very quick sands of 600, then 800 to make the sanding marks more finite. After that the whole post was sanded down to matte finish using 3M's 026201 Sanding Pads.
Logos were sanded off with 400grit sand paper, and they went rather quickly. Then followed with very quick sands of 600, then 800 to make the sanding marks more finite. After that the whole post was sanded down to matte finish using 3M's 026201 Sanding Pads.
Exp001 || Other projects in the works.
By page 5, I may be beating the band on the accolades but this is a great build. Smart where it needs to be, pushing limits where it can.
How is the SMUD saddle working out? It looks to be a budget friendly version of the MCFK saddle with a few mm differences.
The exogram crank (among numerous other pieces of this build) appears to be a great value/performance choice. Nice to see the improved Q factor and weight vs the older Reds. What was your method to remove the decals?
I know the non-black items are being pointed out in one way or another on this thread but I think it adds a nice bit of character.
Charcoal black + a bit of hotness reminds me of hot coals ready to burst into flames.
Nice photo-shoot location too!
How is the SMUD saddle working out? It looks to be a budget friendly version of the MCFK saddle with a few mm differences.
The exogram crank (among numerous other pieces of this build) appears to be a great value/performance choice. Nice to see the improved Q factor and weight vs the older Reds. What was your method to remove the decals?
I know the non-black items are being pointed out in one way or another on this thread but I think it adds a nice bit of character.
Charcoal black + a bit of hotness reminds me of hot coals ready to burst into flames.
Nice photo-shoot location too!
- prendrefeu
- Posts: 8580
- Joined: Wed Oct 31, 2007 10:32 pm
- Location: Glendale / Los Angeles, California
- Contact:
Thanks for the compliments, I really appreciate that!
I absolutely love the SMUD saddle, already ordered a second as backup (and for another bike) and I'm confident in its quality. Premium stuff!
The cranks:
Basically for what I did it was sanding -> lots of patience -> 2k clearcoat (light) -> Opti-clear.
I started off the 320grit wet sand paper, then as I started to rub off decals I switched to 400. Shortly after the decals were removed I moved on to 600, then 800. By this time I'm down to the bare carbon (I'm sanding everywhere). Be careful not to sand too much near the axle or the pedal threads as the carbon layers are thinner on the edges and you'll go right through them, making the interface look uneven.
After that I got a hold of some spray can 2K clearcoat from an auto paint supply shop and applied a very light coat because I wanted the clear coat physical protection. Optionally you can just apply Opti-clear or 303 Spray for an ultra-thin UV-only protectant from there, but I wanted a little physical protection as well. After the 2K dried, a lightly sanded it smooth with an ultra fine steel wool pad (very lightly!) and then applied the opti-clear for the permanent UV protection. Plus I was applying Opti-clear to all the other parts on my bike so I wanted to be sure that everything got the same treatment.
I absolutely love the SMUD saddle, already ordered a second as backup (and for another bike) and I'm confident in its quality. Premium stuff!
The cranks:
Basically for what I did it was sanding -> lots of patience -> 2k clearcoat (light) -> Opti-clear.
I started off the 320grit wet sand paper, then as I started to rub off decals I switched to 400. Shortly after the decals were removed I moved on to 600, then 800. By this time I'm down to the bare carbon (I'm sanding everywhere). Be careful not to sand too much near the axle or the pedal threads as the carbon layers are thinner on the edges and you'll go right through them, making the interface look uneven.
After that I got a hold of some spray can 2K clearcoat from an auto paint supply shop and applied a very light coat because I wanted the clear coat physical protection. Optionally you can just apply Opti-clear or 303 Spray for an ultra-thin UV-only protectant from there, but I wanted a little physical protection as well. After the 2K dried, a lightly sanded it smooth with an ultra fine steel wool pad (very lightly!) and then applied the opti-clear for the permanent UV protection. Plus I was applying Opti-clear to all the other parts on my bike so I wanted to be sure that everything got the same treatment.
Exp001 || Other projects in the works.
Sweet Jesus, that's sick
Nice work. Really nice
Technical Director at www.TUFFcycle.com
-
- Posts: 632
- Joined: Tue Apr 05, 2011 7:41 pm
Great build Prend, it seems the Uno Stem is bargain of the century at $20. Did you acetone off the logo's? just picking one up on ebay today......
- prendrefeu
- Posts: 8580
- Joined: Wed Oct 31, 2007 10:32 pm
- Location: Glendale / Los Angeles, California
- Contact:
Yes, acetone will take the logs right off!
Exp001 || Other projects in the works.
-
- Posts: 632
- Joined: Tue Apr 05, 2011 7:41 pm
Prend, I keep coming back to your build for inspiration longer term. Unless I missed something can you tell me about the bars? Where did you source, How'd you like them? cheers..
- prendrefeu
- Posts: 8580
- Joined: Wed Oct 31, 2007 10:32 pm
- Location: Glendale / Los Angeles, California
- Contact:
KAC,
Yes, at some point eventually. For now Stoked! might be limited to components and smaller parts just do to limited capital to get things launched. I've been working with a friend on a few things, and working on other components solo. Hopefully we'll have something to the market by the end of the year (it's a slow, back burner type project for now).
... Then, eventually we'd love to buy a laser sintering machine, a loom, a 4x8 large bed laser cutter, and a big ol'autoclave. We've got ideas.
Yes, at some point eventually. For now Stoked! might be limited to components and smaller parts just do to limited capital to get things launched. I've been working with a friend on a few things, and working on other components solo. Hopefully we'll have something to the market by the end of the year (it's a slow, back burner type project for now).
... Then, eventually we'd love to buy a laser sintering machine, a loom, a 4x8 large bed laser cutter, and a big ol'autoclave. We've got ideas.
Exp001 || Other projects in the works.
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com