Kettle Cycles Carbon Rotors
Moderator: Moderator Team
-
- Posts: 163
- Joined: Thu Jul 17, 2008 9:37 pm
If you guys haven't already, there is a massive thread about these rotors over at MTBR, in the Brake forum. The issue of the out-of-true rotor has even come up, and in the case of that specific poster, they didn't have the rotor mounted up perfectly, which caused it to rub at one point on its rotation.
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
I have already removed/remounted the rotor prior to my previous post and that did not resolve the issue. Just perused the last few pages of that thread, starting with were folks started receiving rotors and did not see any other posts about rotors being out of true.lordconqueror wrote:The issue of the out-of-true rotor has even come up, and in the case of that specific poster, they didn't have the rotor mounted up perfectly, which caused it to rub at one point on its rotation.
- Michael
"People should stop expecting normal from me... seriously, we all know it's never going to happen"
"People should stop expecting normal from me... seriously, we all know it's never going to happen"
-
- Posts: 163
- Joined: Thu Jul 17, 2008 9:37 pm
lame. i guess it's time for you to fill out the online customer service request form they are so insistent on people using, so they can get you sorted.
Actually I see that as being very customer oriented. So this morning again removed the rotor but this time laid it flat on a granite countertop which indicated the rotor was within +/-2mm of laying flat along the brake track. I also placed the wheel in the truing stand (budget model for basic truing), and using a micrometer, was able to make some adhoc checks for hi/lo variation on the face of each of the rotor disc mounts. I did this by placing the micrometer flush against the arm of the stand and measuring the differences between each of the 6-mounts which varied from as little as .05mm to possibly as much as .50mm. This seems like a very small degree of variation but since it is near the center of the rotors rotation, I am guessing that the lateral variance would be amplified further out along the surface of the rotor. At this point, I am thinking I might need to check with a local machine shop than turned the flanges off my hollowgram spindles to see if they also mill the hub's disc mount faces to much tighter tolerances.
- Michael
"People should stop expecting normal from me... seriously, we all know it's never going to happen"
"People should stop expecting normal from me... seriously, we all know it's never going to happen"
Or rotate the rotor on the hub by a couple of bolt holes and see if the high / low spots follow the rotor or stay with the wheel...
ms6073 wrote:Actually I see that as being very customer oriented. So this morning again removed the rotor but this time laid it flat on a granite countertop which indicated the rotor was within +/-2mm of laying flat along the brake track.
not sure of the whole story but +/- 2 mm runout is far too much. any rotor I have that is fitted to my wheels is well within within 0.5 mm, or +/- 0.25mm (haven't measure any but just by looking)
- stephen@fibre-lyte
- in the industry
- Posts: 605
- Joined: Thu May 29, 2008 12:22 am
- Contact:
That's what I was thinking. 2mm is an awful lot for a brake track to be out, especially on something so small. Is it 2mm extra thickness or is it the same thickness all over but out of flat by 2mm?
-
- Posts: 193
- Joined: Wed Apr 16, 2008 7:43 am
- Location: Sapporo City, Hokkaido, Japan
- Contact:
Anybody using/used these rotors on Formula R1? Seems like a very tight fit into the calipers.
-
- Posts: 596
- Joined: Mon Sep 27, 2010 8:38 am
Any comments on the brittle-ness of the rotor? On cars, rotors are pretty shielded. On MTBs, they're sort of out there in the wind.
I took delivery of mine (a 160 SFL), and then decided to stick with my Scrubs. I listed it for sale hedre, but no one bought it. So I decided to have a go at it, and mounted it up. Dead-on true mine is. no wobbles. still in the process of properly breaking it in, so i'll report later on its maximum abilities.
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com