I just swapped out a Reynolds freehub from Campag to Shimano. When I pulled the hub off, there was a white grease...but i their tech doc...they recommended Slick Honey

_________________

Hi,

You won't hear me complaining if by some miracle all that white grease were to be turned into honey....

O.K...So by dismantling the hub you found or more likely did not find what you were expecting?

Maybe you should consider writing a book along the lines of "How to recognize your Saints" but based on recognizing grease instead?

Ciao,

_________________
Being a snob is an expensive hobby.

Red Devil grease sure reminds me of the old Bullshot grease too. Super Web grease is totally different. Think string cheese. Softer, gooey-er.

Hi thisisatest, thanks

The freewheel noise of my Lightweights has been driving me crazy since I bought them I hate loud ratchets.

I thought because Carbonsports sell them dry (no grease) that was how they were supposed to be.

Came across this thread on Thursday evening, and immediately ordered some DTSwiss "Special" grease. Applied it today, and it runs super quiet now. Love it.

Super thanks for this thread.

_________________
Di2x2

OK, that's an interesting tip. But from where do you source this Krytox PFPE stuff? I consulted google with no particular success, at least for a European source.

Hi,

Krytox is a Dupont De Nemours brandname just in the same way Teflon is.
It is however not so easy to source in Europe for an individual as the only bicycle related company that uses it AFAIK is Ceramic Speed.
Through their dealers or directly from them (whatever access you can get through your status) you can purchase syringes filled with Krytox loaded grease. Type 225 I think it is, which to my taste and use is a little to high in viscosity. IOW, a little too thick.
In France you'd get it from Dulight, for instance, but I'm well aware the internet isn't really offering much of it to the punter.

Personally I came in touch with it through a Finish Line product who are still offering a chain lube based on a wax lube loaded with Krytox. While I wasn't all that impressed by the wax on a chain I was absolutely excited by the effect of the Krytox when I lubed my aging Bora Ultra USB bearings with it.
The wax is easily separated from the rest of the lube by just letting it sink to the bottom of the container. You don't want the wax in your bearings as it tends to solidify once the solvents have flashed off.

If it's oil with Krytox as an additive you're after then the only way to get it is by buying it from the USA. I intend to do this but I do not as yet know if it can be shipped freely as a chemical. (I think it's OK)
It is also a great product to use on bushing type bearings such as found in pedals, pulleys and indeed freehubs.

In a nutshell it enters and bonds to a metal surface and stays there to reduce friction. Once added it is very difficult to undo.
Reducing friction alos reduces wear so that makes it a win-win, Krytox or not.

Ciao,

_________________
Being a snob is an expensive hobby.

Hi WeightySteve, yes you are right

Freehubs should come with grease or oil, or should come with instructions which indicate the recommended grease or oil that should be used on the ratchet teeth, pawls, and seals

Thanks for the reply!

So maybe this ebay offered product is the stuff to go for? (seems as if they ship worldwide): http://www.ebay.com/itm/DUPONT-KRYTOX-G ... 0608496816" onclick="window.open(this.href);return false;

Hi,

That one should work fine.

This is the one I had in mind for bearings:

http://www.derbychamp.com/Krytox-GPL-100-p/760.htm

Ciao,

_________________
Being a snob is an expensive hobby.

Hi fdegrove, do you think Krytox is that good that you are happy to use it as an oil

How many kms have you noticed before you need to re-oil ... thanks

Hi,

Let me just say that wherever one would consider to use PTFE (aka Teflon) loaded oil, Krytox does a far better job.
So much so that I don't understand why its use is not more widely spread.
Maintenaince would be similar to but possibly reduced compared to all other stuff run on oil.

Used in the right places it really is the best oil additive I know of.

Ciao,

_________________
Being a snob is an expensive hobby.

Hi fdegrove, thanks, do you know if Krytox can be mixed with lithium or aluminum based marine greases w/o any issues arising?

Also, can Krytox be used with ceramic bearings w/o any issues arising?

Hope you don't mind me asking ... I know some chain oils (if it gets passed the seals) can damage hub and jockey wheel ceramic bearings and not all oils and greases mix together ... thanks

Hi,

Not being a chemical engineer, I'm afraid I can't really answer that. However, from the little I know, I'm not quite understanding why you'd actually want to do that for cycling purposes.
Krytox grease does exist in a variety of viscosities suiting an equal number of applications. Depending on load, revs, exposure to contaminants and what have you.



Absolutely.
From my perspective there's little use for a hybrid ceramic bearing unless you lube it with Krytox grease (which is what the guys at Ceramic Speed do) or be more adventurous and use oil. (Krytox oaded oil, that is)
One proviso for the latter is that you may need an arguably deeper pocket in that it may not last that long, it obviuosly will need more frequent relubing too.

There really is no industrial bearing that is factually nor actually designed and lubed correctly for cycling use. They are all designed with heavy loads and high revs in mind.

As an engineering consultant CEO we used to say "ce qui peut le plus peut le moins" , which boils to let's overdesign the thing so we'll know it will work and last.
In cycling you need to put that compromise in a different perspective. You want the best possible performance at really low revs, low load and low friction. None of these bearings are designed with that in mind and as counterinuitive as it it may seem what could do more than what it was designed for is now actually dragging you down.

The ideal type of bearing for cycling purposes is (a few exceptions notwithstanding) the cup and cone bearing. It was what has been used and choosen years ago by engineers and still is to this day the best choice overall from an engineering POV as well as a performance POV.

That's my POV from an ideal world's perspective anyway.

Ciao,

_________________
Being a snob is an expensive hobby.

Hi fdegrove, thanks, I was thinking perhaps after applying the oil, which bonds to all surfaces, if a liberal amount of grease could then be applied as a backup ...