That is a design that would be awesome. Thinking of a FSA plasma style bar that is pre built and then on demand after a fitting the stem tube length is selected and then bonded to the bars. From the front the bars are super clean as the bond is in the stem tube. Would just need a clean way to set bar angle for different degree stems.

I'll think about it. Otherwise a formum member contacted me, and offered me a very nice handlebar that could be used for a prototype bar/stem combo with my own stem. So if I get it I'll try to make it, really appreciate (thanks to Jamie from Australia!)

Otherwise it's almost finished...I just have to polish it a bit etc., so it will be finished during this weekend, will send then some more photos:

_________________
Berk PROTO-TYPE Composites - Handmade In Slovenia
Berk Composites

Looks great
Really smooth and slimmed, i like it...

Mary me Jure.

_________________
Storck Fenomalist 6.3kg.
BMC Teammachine SLR01

absolutely fantastic job on that bar/stem Berk.

very neat trick there, cosmetic done without breather or peel. very smart.

_________________
www.crumptoncycles.com

Thanks!

@nicrump
Thanks for the compliment, really appreciate that from someone like you! If I'm honest it turned out better than I hoped. It was a bit tricky to make sure that the vacuum bag didn't "cut" in the carbon, to provide the nice finish, but it was more than worth the extra effort. Also the layup under the cosmetic layer was very important, I didn't wanted to get any "edge" between each layer if you know what I mean, and it turned out really nice.

I'll soon make some more photos, also from the front profile.

_________________
Berk PROTO-TYPE Composites - Handmade In Slovenia
Berk Composites

what is the final weight of it?

Very very nice
is it possible with all kind of stem and handlebar ?

It's basicly the same, when I started it was 300g, now it's 2g less as on photo. If I wouldn't cover also the stem and the part between the joint and the handlebar tape I would save almost 10g.

@steff
Sure, anything would be possible. In the future I'll most probably try to make my own stem and laminate it to a bar, will see, I'll for sure let you know if/when I start with it.

_________________
Berk PROTO-TYPE Composites - Handmade In Slovenia
Berk Composites

Hello Berk.
I have been watching your thread for a while and I have to say I am very impressed with your work. Very meticulous with an incredible attention to detail. I do a lot of composite work with my university here in the states and we were having issues with the bag cutting into the plys and we switched to stretchy vacbag. Stretchlon to be exact. Stretches to 400% and makes your life much easier. You just can't reuse it. But then again, you seem to be doing fine without so keep doing what you're doing.

Hi, thanks! Yes I also use it sometimes, for example when I made my frame (green foil) and for some more complex shapes/moulds. I never use the same bag for 2 products, so I could make it also with strechlon, but somehow prefer the ordinary foil for the vacuum bag.

_________________
Berk PROTO-TYPE Composites - Handmade In Slovenia
Berk Composites

ok , thanks because I have Nora stem and mcfk handlebar and a combo will match perfectly with my seatpost combo

300g? that´s heavy did you made it for cyclocross?

The reinforcements added around 20g for the joint + cosmetic layer, so the weight depends from the origina bar and stem.

@steff
it would be for sure possible to make it. It's even less complicated than that combo that I just made (because that type of clamping mechanism where I could just cut the area where the two bolts are and glue the bar in the stem, and then just add a few more carbon reinforcements).

_________________
Berk PROTO-TYPE Composites - Handmade In Slovenia
Berk Composites

Berk, slightly off the current topic, but did you get feedback from the Sky team on the seat and post combos you made them? Are they going to use them this year?

_________________
Scott CR1 - 12.84Ib