Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Blog NEW Galleries NEW FAQ Contact About
It is currently Tue Jun 28, 2016 7:24 am
Recently the board software has been updated and there are some known bugs/failures:
- Avatars are currently not being displayed ✔ FIXED
- Tapatalk connection is currently broken ✔ FIXED
- Avatars cannot be uploaded ✔ FIXED

Please note that we will soon do some changes in WW board template design in case to get a fully mobile/desktop responsiveness board!
If you find more errors please post it here: http://weightweenies.starbike.com/forum/viewtopic.php?f=7&t=139062


All times are UTC+01:00





Post new topic  Reply to topic  [ 22 posts ]  Go to page Previous 1 2
Author Message
PostPosted: Mon Oct 22, 2012 8:28 am 
Offline

Joined: Fri Oct 07, 2011 2:08 pm
Posts: 1365
David Blaine


Top
   
PostPosted: Mon Oct 22, 2012 1:52 pm 
Offline

Joined: Wed Mar 28, 2007 12:49 pm
Posts: 1590
Location: Near Horgen, Switzerland
The ez out is possible. But much easier just to drill the bolt head, particularly if you used a lightweight aluminium bolt. Start with the largest drill which fits into the allen socket and drill down maybe 3-4mm until the bolt head drops off. Should be possible to do this without damaging even the top cap.

Another alternative is to grind down a slightly larger allen key with a slight taper, then hammer it into the bolt head and unscrew. You need a bench grinder and a steady hand to do this. It takes a long time to do properly, but enables you to unscrew and possibly re-use the bolt. I've used this technique for exotic aero bar bolts which cannot be replaced.


Top
   
PostPosted: Mon Oct 22, 2012 2:33 pm 
Offline

Joined: Mon Oct 22, 2012 5:30 am
Posts: 22
Location: Santa Monica, ca
Did you get it off?


Top
   
PostPosted: Mon Oct 22, 2012 10:03 pm 
Offline

Joined: Tue Nov 11, 2003 9:47 pm
Posts: 2177
Location: Santa Cruz, California, USA
stella-azzurra wrote:
Eric, extractors are made to extract bolts. This is a puny top cap bolt which is low torque. We are not talking about a rusted bolt that is seized. Please.


The extractors break when you get them in the screw and accidentally put side force on them. The small diameter ones snap very easily.

But hey, if you think I'm full of it, go for it.


Top
   
PostPosted: Mon Oct 22, 2012 10:28 pm 
Offline

Joined: Mon Jan 02, 2006 7:10 pm
Posts: 497
If it will not loosen by turning the stem, I would quite quickly just go for drilling it out. Find the guy or girl you know who is best at this kind of off-the-cuff work and get them to help. With the right set-up it is a 5 minute job, including a tea-break, and you can just insert a new bolt and be on your way.

Key is setting up with a good central drilling position, with the stem clamped firmly down, and preferably a mounted drill. Use a drill bit of the right size (smaller than the head of the stripped bolt) and then drill until you can thin the shoulder of the bolt. It will then come free with some encouragement. Good luck.


Top
   
PostPosted: Mon Oct 22, 2012 10:49 pm 
Offline

Joined: Sun Sep 28, 2008 2:23 am
Posts: 655
Location: so. cal.
i already removed it. i wanted to the stem turning solution to work, but my stem has only a 2mm spacer and was not able to turn. my dad is a handyman and he lend me the extractor bolt. but what i ended up doing is getting a hex bit that barely fit in and lightly hamer it in and carefuly turn it until it loosened.


Top
   
PostPosted: Mon Oct 22, 2012 10:58 pm 
Offline

Joined: Sun Sep 28, 2008 2:23 am
Posts: 655
Location: so. cal.
the next question is has anybody tried another cap expander on a look 595 (like tune gum and tune cap). if so how how does it work compared to the stock one.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 22 posts ]  Go to page Previous 1 2

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. Stripped bottle cage bolt thread - best workaround?

in Road

DrJeffers

13

748

Wed Mar 23, 2016 11:39 pm

pavel View the latest post

There are no new unread posts for this topic. Remove red bolt from non-drive side ROTOR 3d+

in Road

SQUICCHI

2

381

Mon Nov 09, 2015 7:51 pm

SQUICCHI View the latest post

There are no new unread posts for this topic. Can you remove the decals on the Roval CLX wheelset?

in Road

bencolem

4

1055

Sun Jun 05, 2016 7:02 am

gangbyeon View the latest post

There are no new unread posts for this topic. How to remove sealant from tubular tire?

in Road

wootenlakeguy

11

742

Sat Jan 02, 2016 1:19 pm

1415chris View the latest post

There are no new unread posts for this topic. Remove guts from Super Record brifters?

[ Go to page: 1 2 ]

in Road

biki

19

1237

Sat Mar 26, 2016 11:33 pm

bikerjulio View the latest post


All times are UTC+01:00


Who is online

Users browsing this forum: MSNbot Media, physeter, sanrensho, Yahoo [Bot] and 20 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited