"Low" power readings (badly mounted power2max cranks?)
Moderator: Moderator Team
Recently purchased a power2max power meter with rotor 3d+ cranks. After doing a couple of TTs some friends asked me about the figures and told my that my avg watt seemed low. Now I can't say for sure because I've never done any testing in a lab or such to get exact figures but I still wanted to ask just to get some input. May it be that my cranks are badly mounted which makes me get "low" readings?
What I have to show is a intervall session I did on my kurt kinetic road machine. And the numbers are taken from the power2max crank and calculated data using a plugin to ST3 called trainer power (by mechgt) with the resistance curve for my trainer. Supposedly the kurt kinetic road machine should give reliable power numbers.
Power2max:
St3-plugin:
What I have to show is a intervall session I did on my kurt kinetic road machine. And the numbers are taken from the power2max crank and calculated data using a plugin to ST3 called trainer power (by mechgt) with the resistance curve for my trainer. Supposedly the kurt kinetic road machine should give reliable power numbers.
Power2max:
St3-plugin:
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
-
- Posts: 616
- Joined: Sun Nov 13, 2011 6:00 am
Well, first off tell us a bit more. Weight. Height. Age. It all changes the definition of "low". Look around the Training Peaks blog it has some good information about what the pros put out and there is a chart somewhere that shows w/kg required for certain amounts of time in different levels of the sport, ie pros can do x w/kg for 1,2,5,20,60etc mins vs cat 1 recreational rider etc. Someone will have a link. I cant seem to find it on my phone.
-
- Shop Owner
- Posts: 1980
- Joined: Sat Jun 13, 2009 4:02 am
- Location: NoVA/DC
kinetic has a cheap computer with a reading that gives you power numbers based on its trainer's speed (it basically knows the force required to turn the resistance unit). you can get it and compare to at least see if youre in the ballpark. or borrow someone's powertap hub
I'm 85kgs (187lbs), 193cm (6.3 feet and inches), 27 years old.
Haven't had the p2m cranks for that long but I have some data from an actual TT-race which was run on a fairly flat circuit of two laps.
Distance: 33,59 km
Climb: +113,9 / -122,4
Time: 45:51
Avg speed: 44,0 km/h
Avg power: 324,4
Weather conditions: Min./Max.: 16,4 °C/17,0 °C; Pressure: 1015,1 mbar; Humidity: 91,2%; Dew point: 15,2 °C; Wind Speed: 6,7 km/h; Precipitation: 0,0mm
What I'm aiming for is to find out if I can't trust the numbers (don't know how daft it seems or is not trusting a power2max power meter). I'm afraid I can't borrow another power meter this is what I have. The numbers generated for the kurt kinetic is with the resistance curve from kurt kinetic them selves. And is claimed to be accurate and "matched" with a powertap.
Haven't had the p2m cranks for that long but I have some data from an actual TT-race which was run on a fairly flat circuit of two laps.
Distance: 33,59 km
Climb: +113,9 / -122,4
Time: 45:51
Avg speed: 44,0 km/h
Avg power: 324,4
Weather conditions: Min./Max.: 16,4 °C/17,0 °C; Pressure: 1015,1 mbar; Humidity: 91,2%; Dew point: 15,2 °C; Wind Speed: 6,7 km/h; Precipitation: 0,0mm
What I'm aiming for is to find out if I can't trust the numbers (don't know how daft it seems or is not trusting a power2max power meter). I'm afraid I can't borrow another power meter this is what I have. The numbers generated for the kurt kinetic is with the resistance curve from kurt kinetic them selves. And is claimed to be accurate and "matched" with a powertap.
i also have a kurt kinetic trainer. i don't think their power curve is very accurate, or it never was for me and i don't worry about it now i have a power meter anyway.
are you doing the spin down test to calibrate the turbo before you use it and do you set the tyre pressure the same every time
anyway - 324 watts is a good power output, if thats noticeably low then
and 44km/h seems like good going as well but your speed would depend on conditions and how aero you are.
here is a thread I've been looking at recently with some testers power outputs on http://www.timetriallingforum.co.uk/ind ... opic=70736
are you doing the spin down test to calibrate the turbo before you use it and do you set the tyre pressure the same every time
anyway - 324 watts is a good power output, if thats noticeably low then
and 44km/h seems like good going as well but your speed would depend on conditions and how aero you are.
here is a thread I've been looking at recently with some testers power outputs on http://www.timetriallingforum.co.uk/ind ... opic=70736
Popular TT distance in the UK is 10 miles. Reference is power to beat 20 minutes for this distance...
+1 regarding the trainer data. I know from experience that the wheels, tyres, setup and so on can make a big diffrence to how the trainer rides.
At the end of the day it does not matter what power number you hit, as power numbers don't win races. Instead you just need to be reasonably sure that the power meter produces a consistent measuremtn, and that the numers move upwards. So you might try riding the same circuit every month and noting the wind and time. If the power numbers go up and the time comes down then you are doing something right.
At the end of the day it does not matter what power number you hit, as power numbers don't win races. Instead you just need to be reasonably sure that the power meter produces a consistent measuremtn, and that the numers move upwards. So you might try riding the same circuit every month and noting the wind and time. If the power numbers go up and the time comes down then you are doing something right.
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com