HOT: Active* forum members generally gain 5% discount at starbike.com store!
Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Articles FAQ Contact About




Post new topic Reply to topic  [ 8 posts ] 
Author Message
PostPosted: Sat Aug 18, 2012 3:21 am 
Offline

Joined: Wed Sep 16, 2009 10:25 am
Posts: 129
Location: Australia
I'm going to upgrade my brakes to the xtr m985's and normally you can buy them as a front and rear kit pre bled and ready to go.
The question I have is that I'm one of those that uses the right hand lever for the front brake. The front kit comes with a 'left' lever. Can you flip the left lever into a right, or do I need to buy the right lever separately? Thanks


Top
 Profile  
 
Posted: Sat Aug 18, 2012 3:21 am 


Top
  
 
PostPosted: Sat Aug 18, 2012 3:41 am 
Offline
Shop Owner

Joined: Sat Jun 13, 2009 4:02 am
Posts: 1951
Location: NoVA/DC
the lever is not reversible.
if you are buying a front and rear set, you dont need anything extra. just put the levers where they go and the calipers where they go, and then just remove the hoses from each lever and install them opposite. done.


Top
 Profile  
 
PostPosted: Sat Aug 18, 2012 8:53 am 
Offline

Joined: Thu Jan 13, 2011 4:04 pm
Posts: 508
Location: Sunny UK
as ^^^^ says, swap the hoses over - most likley will need to be bled


Top
 Profile  
 
PostPosted: Sat Aug 18, 2012 2:29 pm 
Offline
User avatar

Joined: Thu Mar 17, 2005 3:25 am
Posts: 2174
Location: Southern Indiana USA
All Avid brakes are reversible. In fact, if you notice on closeout there are often only rear brakes left (since dealers know they can switch them) and I often buy 2 rears at a discounted price and all you have to do is shorten the front hose. Avid includes the barbs to shorten the hose with their brakes.

In fact I just did this last night. I bought a pair of Elixer CR rears for $130 each landed in order to upgrade a bike from Jucy 7's. All I had to do was shorten the hose of the front and then bleed it and I was good to go.

_________________
For certain parts stiffer is more important than lighter.


Top
 Profile  
 
PostPosted: Sat Aug 18, 2012 4:24 pm 
Offline

Joined: Mon Aug 11, 2008 10:08 pm
Posts: 330
Location: Hull
Xt and xtr brakes come with spares olives and other stuff to shorten or change hoses. My brakes came with left as front I swapped over and shortened hoses and didn't need to bleed the brakes after


Top
 Profile  
 
PostPosted: Sun Aug 19, 2012 8:27 am 
Offline

Joined: Wed Sep 16, 2009 10:25 am
Posts: 129
Location: Australia
Okay thanks for the responses guys.
So one way or another I'll have to cut or swap the hoses. Might need to read up on how to do that first!

Cheers


Top
 Profile  
 
PostPosted: Tue Aug 21, 2012 5:18 pm 
Offline
User avatar

Joined: Sun Jun 17, 2012 3:45 am
Posts: 100
If you are careful you should not have to bleed after swapping/shortening the hose. If it was Avid, you would have to bleed it.

_________________
My drawings:
http://www.facebook.com/andrewlivingstonart
My bike:
http://weightweenies.starbike.com/forum/viewtopic.php?f=10&t=107451


Top
 Profile  
 
PostPosted: Wed Aug 22, 2012 3:34 pm 
Offline
User avatar

Joined: Thu Mar 17, 2005 3:25 am
Posts: 2174
Location: Southern Indiana USA
Not true! I have successfully shortened and Avid CR brake this weekend without bleeding and it is just as stout as the other one. I have between my and wife bikes 4 sets of CR and 2 sets of Jucy7 and I have shortened all of them. When I first started, I always had to bleed. Now that I know what to do, I never have to bleed. The key for me was to make the cut in the hose at the correct new length then raise the caliper end of the hose and to start with the lever end facing slightly uphill. Then with a rag under the cut off piece, loosen the squish bolt keeping the lever open end pointed up. Put the screw in part of the compression fitting in the caliper end while keeping it up. Put the compression part on, insert and tighten.

_________________
For certain parts stiffer is more important than lighter.


Top
 Profile  
 
Posted: Wed Aug 22, 2012 3:34 pm 


Top
  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 8 posts ] 


Who is online

Users browsing this forum: AdyM, Google Adsense [Bot] and 10 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. Crankset - light alternative to XTR M980/M985?

in MTB

RedRacer

3

899

Mon May 06, 2013 4:10 am

UpFromOne View the latest post

There are no new unread posts for this topic. m985 crank bigger gap for crank arm bolt to spindle?

in MTB

tzeonn

0

816

Tue May 14, 2013 7:49 pm

tzeonn View the latest post

There are no new unread posts for this topic. Broken Sram Rival Lever

in Road

Bregnhoj

4

351

Tue Oct 29, 2013 5:43 pm

stella-azzurra View the latest post

There are no new unread posts for this topic. Colnago Master - Shift Lever Bosses

in Road

ianSWBB

0

186

Thu Apr 03, 2014 12:15 pm

ianSWBB View the latest post

There are no new unread posts for this topic. Avid Short Ultimate Canti-lever Brakeset

in For sale - Pictures are mandatory 22-3-13

Ordinaybikes

0

105

Fri Feb 21, 2014 3:30 am

Ordinaybikes View the latest post


It is currently Wed Apr 23, 2014 12:02 pm

All times are UTC + 1 hour




Advertising   –  FAQ   –  Contact   –  Convert   –  About

© Weight Weenies 2000-2013
hosted by starbike.com


How to get rid of these ads? Just register!


Powered by phpBB