AERO brakes
Moderator: robbosmans
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
You caught me with that angle
Unfortunately the frame would look a bit funny without decals on the downtube. The plasma 3 mechanical is really a hack job of the original plasma TT. For the bottle cage bosses they basically cut out a part of the frame and glue in some metal inserts (they aren't molded in). I ended up smoothing that portion with some bondo and spraying it black, so there is a bit of a rectangle that is black around that area. This is so I can apply the decals over the bulge for the bosses.
http://university.tri-sports.com/wp-con ... ma1415.jpg
I'll post another thread for the bike, don't want to spam this one too much.
To clarify, the omega brakes seem to be as good as the tektro centerpull setup I had on my nosecone shiv, which is pretty darn good.
Unfortunately the frame would look a bit funny without decals on the downtube. The plasma 3 mechanical is really a hack job of the original plasma TT. For the bottle cage bosses they basically cut out a part of the frame and glue in some metal inserts (they aren't molded in). I ended up smoothing that portion with some bondo and spraying it black, so there is a bit of a rectangle that is black around that area. This is so I can apply the decals over the bulge for the bosses.
http://university.tri-sports.com/wp-con ... ma1415.jpg
I'll post another thread for the bike, don't want to spam this one too much.
To clarify, the omega brakes seem to be as good as the tektro centerpull setup I had on my nosecone shiv, which is pretty darn good.
- Pokerface07
- Posts: 213
- Joined: Wed Jun 06, 2012 11:43 pm
Mikmik wrote:What aero chainring is that?
Looks like a Rotor Q-Ring with the previous generation graphics. I had the same on mine before they updated the graphics.
Twitter: @FormerTTchamp https://twitter.com/FormerTTchamp
BmanX wrote:No it will not but to be honest those brakes are total overkill anyways.
Whatevs. I have been on old single pivot brakes ages ago. And I really like the brakes of today from the high end models from Shimano and Campy. Better braking is never overkill for me.
-
- Posts: 141
- Joined: Wed Jun 22, 2011 9:39 pm
No road test yet, they only dropped onto my door step this morning, but will take them out on wednesday nights Club TT. Very firm feel on the turbo anyway, and enough spring tension to return my levers (which are unsprung).
Really slick setup, although i'd hope as much given they are pretty much designed for the P3 (which is what I've put them on.)
A little effort required to set them up well, but not much more than any other single pull brake. Had a little bit of fun around my corima disc, but thats more due to it lovely wiggle than the brakes.
Onto weights, I actually bothered to weight one before I put it on the bike.
Everything in the box including all the extra mounting hardware comes in at 144g!
one complete brake in stock form weighs 123g, 1g less than claimed
With a few lighter bolts and trimming the excess from the mounting bolts I got this down to 117g.
Would love to tell you what i used but they were just light weight bolts lying around in the bits box..
I was using stock 7800 calipers before, So have lost loads of grams of drag with these brakes and a 75g in weight!
(Photos on scales to prove will be uploaded later)
Although much improved on any aero brake I've tried against the rear stays of the P3. I might try to make a subtle electrical tape fairing to smooth the small step up from stays to the brake.
Really slick setup, although i'd hope as much given they are pretty much designed for the P3 (which is what I've put them on.)
A little effort required to set them up well, but not much more than any other single pull brake. Had a little bit of fun around my corima disc, but thats more due to it lovely wiggle than the brakes.
Onto weights, I actually bothered to weight one before I put it on the bike.
Everything in the box including all the extra mounting hardware comes in at 144g!
one complete brake in stock form weighs 123g, 1g less than claimed
With a few lighter bolts and trimming the excess from the mounting bolts I got this down to 117g.
Would love to tell you what i used but they were just light weight bolts lying around in the bits box..
I was using stock 7800 calipers before, So have lost loads of grams of drag with these brakes and a 75g in weight!
(Photos on scales to prove will be uploaded later)
Although much improved on any aero brake I've tried against the rear stays of the P3. I might try to make a subtle electrical tape fairing to smooth the small step up from stays to the brake.
I have raced the TriRig Omega in two TTs, one flat course with three fast turns(i.e I didn't use them) and the other an out and back on a rolling course. Also, I have used them in three crits and one road race. I am light at 62kg, but have been searching for a way to get some good braking on my carbon hoops(November, HED, and Bontrager) and have found it with these brakes. I have used Cane Creeks 200SL which are fine on AL, but didn't come close to cutting mustard on the CF stuff. I then swapped to an Ultegra 6500 and while that was much better, I still was sketchy about my slowing. The Omega has given me the utmost confidence in the most technical crits (which one of the three is) and in any RR, where everyone had me wearing my brake pads out today.
Not sure how the gold standard compares or how a heavier rider is going to find them, but I do know I am no longer looking for a brake that allows me to brake when I want. The pads were the same on all the hoops.
I think they might be pretty areo too.
Not sure how the gold standard compares or how a heavier rider is going to find them, but I do know I am no longer looking for a brake that allows me to brake when I want. The pads were the same on all the hoops.
I think they might be pretty areo too.
That post just made my day. Thank you, Stalkan!
Juanmoretime - if you got a thin hex head bolt, could you not use this to attach the plate to the frame by using an open ended spanner rather than allen key? I have the same issue fitting the Shimano AX brake to the rear of my Cervelo P3. If I understand correctly, the Plasma fitting sounds very similar to the Cervelo.
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
Okay, looks to be a different design to Cervelo. Pity it may not fit!
Would love to buy the brake off you, but have been buying too much of late and need to stop...
Would love to buy the brake off you, but have been buying too much of late and need to stop...