Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Blog NEW Galleries NEW FAQ Contact About
It is currently Mon Jul 25, 2016 9:23 pm
Recently the board software has been updated and there are some known bugs/failures:
- Avatars are currently not being displayed ✔ FIXED
- Tapatalk connection is currently broken ✔ FIXED
- Avatars cannot be uploaded ✔ FIXED

Please note that we will soon do some changes in WW board template design in case to get a fully mobile/desktop responsiveness board!
If you find more errors please post it here: http://weightweenies.starbike.com/forum/viewtopic.php?f=7&t=139062


All times are UTC+01:00





Post new topic  Reply to topic  [ 10 posts ] 
Author Message
PostPosted: Fri Apr 06, 2012 4:36 pm 
Offline

Joined: Sat Jan 07, 2012 3:21 pm
Posts: 34
My Ridley's fork does not have fender mounts or the brake hole. I use the bike for wet commuting so am looking for recommendations for a decent fork with mounts. Any good experiences? Would prefer to go all carbon and keep the weight down.

Thanks


Top
   
PostPosted: Fri Apr 06, 2012 5:13 pm 
Offline

Joined: Wed Oct 26, 2011 8:45 pm
Posts: 37
If you are looking for a new fork with fender mounts Whiskey Parts makes one that is a carbon steerer with aluminum dropouts. Whiskey is QBP's house brand and any lbs could get you one. What I did when putting fenders on my race bike was to use zip ties to hold the fenders on. Sure it is not the cleanest look but it is far less expensive then a new fork.


Top
   
PostPosted: Fri Apr 06, 2012 7:38 pm 
Offline

Joined: Sat Jan 07, 2012 3:21 pm
Posts: 34
Agree. The dropout mounts aren't anything I miss, but no brake hole makes it tough to keep the fender tight at the crown. My current zip-tie approach isn't cutting it.


Top
   
PostPosted: Sat Apr 07, 2012 2:09 pm 
Offline

Joined: Wed Oct 26, 2011 8:45 pm
Posts: 37
Give this a try. I drilled two holes in the fender both holes are in the center line of it and big enough to fit two medium zip ties in them one I drilled just in front of the fork and the other in back. I then ran both zip ties on the inside of the fender and out both of the holes so I could make two loops one for each leg of the fork. Put the fender in place and pull your zip ties and you are good to go. Hope this helps, I have used mine all winter like this.


Top
   
PostPosted: Sat Apr 07, 2012 8:36 pm 
Offline

Joined: Fri Jul 28, 2006 1:34 pm
Posts: 157
Location: Midwest USA
Bontrager Satellite Plus road forks, carbon legs, alu steerer and eyelets and bridge hole
http://bontrager.com/model/04036

_________________
adrenaline junkie


Top
   
PostPosted: Mon Apr 09, 2012 2:05 am 
Offline

Joined: Tue Aug 04, 2009 8:40 pm
Posts: 22
I've got an Easton EC90x I've been meaning to get rid of...


Top
   
PostPosted: Mon Apr 09, 2012 5:24 pm 
Offline

Joined: Sat Jan 07, 2012 3:21 pm
Posts: 34
robin3mj wrote:
I've got an Easton EC90x I've been meaning to get rid of...

Has the steerer been cut?


Top
   
PostPosted: Mon Apr 09, 2012 5:25 pm 
Offline

Joined: Sat Jan 07, 2012 3:21 pm
Posts: 34
crosschained wrote:
Give this a try. I drilled two holes in the fender both holes are in the center line of it and big enough to fit two medium zip ties in them one I drilled just in front of the fork and the other in back. I then ran both zip ties on the inside of the fender and out both of the holes so I could make two loops one for each leg of the fork. Put the fender in place and pull your zip ties and you are good to go. Hope this helps, I have used mine all winter like this.

I'd been thinking of trying something like this, but was worried the holes might create a stress point from which the whole fender might crack. But it may be worth a try. Thanks!


Top
   
PostPosted: Mon May 14, 2012 7:26 pm 
Offline

Joined: Sun Mar 23, 2008 7:31 pm
Posts: 361
Very late to this discussion.

If you're looking for a carbon CX fork w/ carbon steer tube and fender mounts, check out the Kenesis Pure CX fork. It's usually available through Pro Bike Kit and I've also seen it on other GB online sellers.

That said, it's pretty easy to mount fenders on any fork (that has enough clearance) by using padded J clamps on the fork legs near the drop outs. They essentially create fender mounting holes down by the dropouts.

For attaching the fender near the fork crown or seat stay and chainstay bridges, if there's not a hole in the fork/frame there, you can easily zip tie the fender at those points using variations of techniques described above. I've seen other uses of J clamps at various locations too, but have never needed to use them. Drilling strategic holes in the fender and good zip ties have always worked and looked reasonably clean.


Top
   
PostPosted: Tue May 15, 2012 6:55 am 
Offline

Joined: Wed Dec 15, 2010 10:32 am
Posts: 452
Location: Estonia
crosschained wrote:
Give this a try. I drilled two holes in the fender both holes are in the center line of it and big enough to fit two medium zip ties in them one I drilled just in front of the fork and the other in back. I then ran both zip ties on the inside of the fender and out both of the holes so I could make two loops one for each leg of the fork. Put the fender in place and pull your zip ties and you are good to go. Hope this helps, I have used mine all winter like this.

:thumbup:

_________________
"Nothing compares to the simple pleasure of a bike ride"
Domane
Ethic 29er
Jamis Renegade Expert


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 10 posts ] 

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. Ritchey WCS Carbon Canti Cross fork vs. ENVE 2.0 Cyclo X

in Cyclocross / Gravel / Touring

timoh

7

833

Sat Apr 23, 2016 8:09 pm

timoh View the latest post

There are no new unread posts for this topic. Carbon fork for cross/gravel build (mind made up, but now the other parts...)

[ Go to page: 1 2 ]

in Gravel

Casati

28

1309

Fri Jul 15, 2016 10:05 pm

Casati View the latest post

There are no new unread posts for this topic. Attachment(s) Out Front Mounts?

in Road

aham23

14

1776

Fri Apr 01, 2016 1:09 pm

GeniuSH View the latest post

There are no new unread posts for this topic. FS: 3x K-Edge Garmin mounts *SOLD*

in For sale - Pictures are mandatory 22-3-13

emorydptt

0

216

Tue Apr 19, 2016 11:06 pm

emorydptt View the latest post

There are no new unread posts for this topic. Lightweight track frame with brake mounts for crit use?

[ Go to page: 1 2 ]

in Road

Devon

16

513

Fri Jul 15, 2016 2:45 pm

Devon View the latest post


All times are UTC+01:00


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited