Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Blog NEW Galleries NEW FAQ Contact About
It is currently Fri Jul 01, 2016 7:16 am
Recently the board software has been updated and there are some known bugs/failures:
- Avatars are currently not being displayed ✔ FIXED
- Tapatalk connection is currently broken ✔ FIXED
- Avatars cannot be uploaded ✔ FIXED

Please note that we will soon do some changes in WW board template design in case to get a fully mobile/desktop responsiveness board!
If you find more errors please post it here: http://weightweenies.starbike.com/forum/viewtopic.php?f=7&t=139062


All times are UTC+01:00





Post new topic  Reply to topic  [ 10 posts ] 
Author Message
PostPosted: Sun Dec 25, 2011 9:14 pm 
Offline

Joined: Fri Jun 03, 2011 6:30 pm
Posts: 90
Anyone out there tried this combo? I am thinking of fitting to Super 6 Evo and don't like the look of the BB, it has very small flanges and the amount in the frame is minimal. Does it damage the frame on install? Is it worth the hassle over SRAM red BB30??

Cheers

L


Top
   
PostPosted: Sun Dec 25, 2011 10:43 pm 
Offline
Shop Owner

Joined: Sat Jun 13, 2009 4:02 am
Posts: 1980
Location: NoVA/DC
by your description, i think youre looking at the "shimano pressfit" bearing set from thm. the PF30 bottom bracket for the clavicula is just like the bb30, just with a larger diameter center section. on the THM website, it says "(without picture / similar to BB30 bearings)"
http://www.thm-carbones.de/accessories-115.html
hope that helps

edit: i would personally use SiSL cranks, or SWorks cranks if i were on a "budget"


Top
   
PostPosted: Mon Dec 26, 2011 9:13 am 
Offline

Joined: Fri Jun 03, 2011 6:30 pm
Posts: 90
I was looking at the correct set - just seems the amount pressed into the frame, ie about 3mm is tiny...


Top
   
PostPosted: Mon Dec 26, 2011 10:51 am 
Offline
in the industry
User avatar

Joined: Sun Dec 16, 2007 9:33 pm
Posts: 713
Location: Luxembourg / Sweden
You are absolutely correct, it is tiny but it does not present a problem on the frames (our) we have used it on, including some rather pedestrian Toray fibered prototypes. I would assume though that there could be a problem with some hi-mod more brittle bb shells.

Our engineer has brought this up with Thomas Mertin who is adamant that his solution works better than inboard bearings. The THM cups do run A LOT freer than the standard Sram inboard Pf bearings, and also a bit better than the ceramic pf bearings we have tried - if you are into that sort of thing..

The SiSl cranks are also very, very good, but I can't help to feel they are a bit let down by the standard SRAM bearings. I just like the feeling of a free spinning crank, don't know if the drag is enough to make any real world pedaling/propulsion difference though.

Costwise in Europe the Cannondale cranks with are pretty much up there with the THM M3s.

_________________
rolobikes


Top
   
PostPosted: Mon Dec 26, 2011 11:50 am 
Offline
in the industry
User avatar

Joined: Wed Jan 19, 2011 11:14 am
Posts: 1376
Location: SYD
thisisatest wrote:
by your description, i think youre looking at the "shimano pressfit" bearing set from thm. the PF30 bottom bracket for the clavicula is just like the bb30, just with a larger diameter center section. on the THM website, it says "(without picture / similar to BB30 bearings)"
http://www.thm-carbones.de/accessories-115.html
hope that helps

edit: i would personally use SiSL cranks, or SWorks cranks if i were on a "budget"



If he's asking after THM cranks then the word "budget" isn't worth mentioning


I have a a set of THM M3s fitted to my BB30 frame using THMs BB30 solution.


It's pretty darn good.

The out board BB system the cranks use feels quite a bit stiffer than campags BB30 system

_________________
Skunkworks Bikes


Top
   
PostPosted: Mon Dec 26, 2011 2:10 pm 
Offline
Shop Owner

Joined: Thu Apr 17, 2008 1:07 am
Posts: 997
Location: San Juan, Puerto Rico
By your original question you mean using the bearings on the frame (like BB30 or PF30) instead of THMs BB that has cups on the outside of the frame?
It's posible as long as the frame is wide enough to acomodate the bearings in the correct position on the Clavicula's axle.
Contrary to other 30 mm universal axle cranks like the Tune Smart Foot, which you can adpat to various BB dimensions....the Clavicula has very specific alloy areas were the bearing will spin as the axle is carbon.

_________________
www.royalbicycles.com


Top
   
PostPosted: Thu Oct 04, 2012 7:48 am 
Offline

Joined: Sun Oct 05, 2008 8:09 pm
Posts: 1329
Location: Aix en Provence
bringing up this old post as I am curious to hear any more feedback on users of Clavicula PF30 BB. How is that combo working out for you and what frame are you using it with ?


Top
   
PostPosted: Thu Oct 04, 2012 8:09 am 
Offline

Joined: Mon Nov 15, 2010 7:58 am
Posts: 339
I have it on my Crumpton SL and haven't had any problems with it.


Top
   
PostPosted: Thu Oct 04, 2012 8:41 am 
Offline

Joined: Fri May 06, 2011 6:31 am
Posts: 76
Using it on my Parlee z3 no problem with creaking.

_________________
Cervelo R2.5
Cervelo P2c
Cervelo R3
Parlee Z3
Parlee TT


Top
   
PostPosted: Thu Oct 04, 2012 11:25 am 
Offline
User avatar

Joined: Thu Aug 25, 2005 7:09 pm
Posts: 1235
Location: In the industry
are u sure u have the pf30 bb for the clav? mine is huge!

_________________
Fast falcons: http://www.youtube.com/watch?v=j3mTPEuFcWk" onclick="window.open(this.href);return false;
www.falcobike.com
Facebook: falcobikeglobal


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 10 posts ] 

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. press fit ceramic bb for my orbea frame ..should i ?

in Road

fh8425

6

443

Sat Feb 13, 2016 1:46 am

fh8425 View the latest post

There are no new unread posts for this topic. Canyon Available in USA in 2017 (Press Release)

[ Go to page: 1 2 3 ]

in Road

krtassoc

44

3921

Fri Jun 10, 2016 6:52 pm

spartan View the latest post

There are no new unread posts for this topic. Press Fit 30, GXP bottom bracket advice needed

in Road

Mr.Gib

13

350

Sat Apr 30, 2016 2:10 pm

rbrtwyn View the latest post

There are no new unread posts for this topic. Bore Hole Diameter of Cyclus BB Press Rings?

in Road

Valbrona

0

265

Sat Aug 01, 2015 2:56 pm

Valbrona View the latest post

There are no new unread posts for this topic. Rotor Press fit 4624 ceramic (bearing removal tool)

in Road

wheelsONfire

2

169

Sat Apr 23, 2016 2:29 pm

wheelsONfire View the latest post


All times are UTC+01:00


Who is online

Users browsing this forum: Bing [Bot], Google [Bot], Yahoo [Bot] and 25 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited