installing CT2 chainrings

Moderator: Moderator Team

Page 1 of 2

[ 16 posts ]

Go to page 1, 2  Next

Print view Previous topic | Next topic

Author	Message
hmai18	Post subject: installing CT2 chainrings Posted: Mon Jun 07, 2010 4:06 am
Joined: Mon May 15, 2006 12:19 am Posts: 457 Location: Kingston, ON	I just ordered a set of Stronglight rings to replace the stock ones that came with my Force crankset (for aesthetic reasons, mostly). Is there a specific orientation for the chainrings relative to the crank arms, or can I just slap them on any which way?
Top

743power	Post subject: Re: installing CT2 chainrings Posted: Mon Jun 07, 2010 4:39 am
Shop Wrench Joined: Sat Nov 29, 2008 6:15 am Posts: 633	They only go on one way. The chain drop pin dictates the big ring position, while the notch in the small ring does the same. Aesthetically, I think the force ones are nicer, because the base of the "feet" on the ct2s are wider than the spider arms on the cranks. _________________ "Any intelligent fool can make things bigger, more complex, and more violent. It takes a touch of genius -- and a lot of courage -- to move in the opposite direction."
Top

hmai18	Post subject: Re: installing CT2 chainrings Posted: Wed Jun 16, 2010 3:03 pm
Joined: Mon May 15, 2006 12:19 am Posts: 457 Location: Kingston, ON	Just received my CT2 outer ring and I see the two holes where the chain drop pin should be. Am I supposed to remove the one from the SRAM rings I have and screw it into the new one?
Top

Redddraggon	Post subject: Re: installing CT2 chainrings Posted: Wed Jun 16, 2010 3:41 pm
Joined: Thu Jul 24, 2008 10:59 pm Posts: 984 Location: North Wales	hmai18 wrote: Just received my CT2 outer ring and I see the two holes where the chain drop pin should be. Am I supposed to remove the one from the SRAM rings I have and screw it into the new one? You should have got one with the chainring (I did with my CT2 ring) _________________ http://www.flickr.com/photos/21993463@N06/ http://twitter.com/JP_Griffiths
Top

hmai18	Post subject: Re: installing CT2 chainrings Posted: Wed Jun 16, 2010 4:00 pm
Joined: Mon May 15, 2006 12:19 am Posts: 457 Location: Kingston, ON	No pin in my package, just the outer ring.
Top

exhibitx	Post subject: Re: installing CT2 chainrings Posted: Wed Jun 16, 2010 4:19 pm
Joined: Thu Oct 02, 2008 3:38 am Posts: 244 Location: Toronto, ON	you don't need the chain drop pin, my rings didn't come with it either just line it up so the pin hole is behind the crank arm pretty sure the sram one won't fit, the sram one i think is just pushed in, the ct2 one is threaded
Top

are	Post subject: Re: installing CT2 chainrings Posted: Wed Jun 16, 2010 4:53 pm
Joined: Fri Sep 05, 2008 1:15 am Posts: 84	What notch in the small ring? I just put ct2 rings on. My big ring did come with a pin to screw in. I lined that up with the crankarm. For the small ring, though, I didn't see anything to indicate orientation, so I just lined up the logos with the big ring.
Top

Gregorio	Post subject: Re: installing CT2 chainrings Posted: Wed Jun 16, 2010 5:06 pm
Joined: Thu Jul 26, 2007 10:24 pm Posts: 1551 Location: Center of the Universe	Stronglight Rings do not come with the pin. I never needed the pin there anyway, I know its purpose but never needed it. _________________ TIME RXR
Top

Redddraggon	Post subject: Re: installing CT2 chainrings Posted: Wed Jun 16, 2010 5:29 pm
Joined: Thu Jul 24, 2008 10:59 pm Posts: 984 Location: North Wales	Gregorio wrote: Stronglight Rings do not come with the pin. They do. They are stapled on the inside of the cardboard sleeve _________________ http://www.flickr.com/photos/21993463@N06/ http://twitter.com/JP_Griffiths
Top

hmai18	Post subject: Re: installing CT2 chainrings Posted: Wed Jun 16, 2010 5:42 pm
Joined: Mon May 15, 2006 12:19 am Posts: 457 Location: Kingston, ON	Well, I'll be damned. I must be totally blind. Thanks!
Top

KWalker	Post subject: Re: installing CT2 chainrings Posted: Thu Jun 17, 2010 8:46 am
Joined: Mon Dec 28, 2009 8:30 pm Posts: 2887 Location: DC	What's this pin you speak of? I unbolted my old rings, bolted these on and was done with it. Pretty damn easy. With the KMC chain they are super quiet and shift really well.
Top

hockinsk	Post subject: Re: installing CT2 chainrings Posted: Thu Jun 17, 2010 6:49 pm
Joined: Fri Jan 25, 2008 2:40 pm Posts: 1981 Location: Kent: UK	The pin stops the chain getting jammed betwwen the arm and the ring if the chain ever overshoots. CT2 rings don't have one fitted in the factory, but stapled to the packaging. Very easy to miss and throw away unfortunately! _________________ Adalta Cycling Club
Top

nathanong87	Post subject: Re: installing CT2 chainrings Posted: Thu Nov 22, 2012 6:11 am
Joined: Mon Jul 18, 2011 2:44 am Posts: 663	Anyone have any idea where to source the pin or an alternative?
Top

Dalai	Post subject: Re: installing CT2 chainrings Posted: Thu Nov 22, 2012 6:35 am
Joined: Wed Dec 15, 2004 10:54 am Posts: 1272 Location: Melbourne, Australia	No, but a very timely bump as mine arrived today. Small plastic bag stapled to the inside of the cardboard sleeve... _________________ http://climbinglama.blogspot.com.au
Top

Tillquist	Post subject: installing CT2 chainrings Posted: Thu Nov 22, 2012 7:11 am
Joined: Fri Dec 30, 2005 3:33 pm Posts: 1317 Location: Denmark	Redddraggon wrote: Gregorio wrote: Stronglight Rings do not come with the pin. They do. They are stapled on the inside of the cardboard sleeve +1 _________________ See My Bike & Tillquist's Kitchen ! A Power2max user..
Top

Display posts from previous: All posts1 day7 days2 weeks1 month3 months6 months1 year Sort by AuthorPost timeSubject AscendingDescending

Page 1 of 2

[ 16 posts ]

Go to page 1, 2  Next