Spoke holding tool?
Moderator: robbosmans
I was just curious what everyone uses to hold their bladed spokes when truing/building a wheel? I have a small set of needle nose pliers that are smooth and I wrap electrical tape around the jaws. But it is somewhat of a hassle to use because the handles hit the other spokes. Is there something better?
I have used something very similar to this little tool from Sapim. I don't know who made the one I use, but it's really nothing special and you could easily make something like this yourself, just make sure that the surface that holds the spoke is big enough so it prevents the spoke from 'tearing' or getting damaged by the tool.
Hope this is of any help.
http://www.sapim.be/index.php?st=products&sub=racetools
Hope this is of any help.
http://www.sapim.be/index.php?st=products&sub=racetools
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
twist resist is nice.
The nice part about a round tool such as from Sapim is that you can keep it around the top half of your finger. It makes adjustment from spoke to spoke very convenient.
I use the Knipex plier wrench which has flat jaws like a Crecent wrench. Twist resist is ok too. The nice thing about a plier tool is that you can use the plier to gently flip from spoke to spoke without letting go of the spoke wrench or having to realign the bladed tool and fit it into the slot, which makes the build go really fast. But I have used a Sapim tool too and it works.
rruff wrote: You could just overshoot 90 degrees and turn back... I've not had a problem with that. Good lube on the threads probably helps, though.
Not very convenient with thin bladed spokes such a CX-Rays. Also, as tension becomes higher the chance of the spoke yielding from twisting increases.
mavic wheels and campagnolo wheels which are pre built with aero spokes come with a black nylon tool similar to the sapim tool.
Most bike shops would have them hanging around in teh workshop from bikes that they've sold with mavic wheels as OEM fitment... or wheelsets they've sold...
I'm sure you could pick them up for a couple of bucks that way...
cheers,
erik
Most bike shops would have them hanging around in teh workshop from bikes that they've sold with mavic wheels as OEM fitment... or wheelsets they've sold...
I'm sure you could pick them up for a couple of bucks that way...
cheers,
erik
Visiting Southwest Western Australia? Visit our store, Crank'n Cycles, in Collie!
lemmy999 wrote:So is the groove in the spacer (or the sapim tool) cut all the way through, or just part of the way through? looks like i could make that from a piece of PVC or the carbon steerer i cut off of my easton fork.
The groove is just deep enough to fit the bladed spoke in. Your idea of using the extra carbon spacer or pvc is exactly what I did.
I had always used a wrench or pliers with electrical tape in the past. But last night I used the cut off piece of the carbon steerer from my Easton fork. It worked really well and is easier and much faster than pliers. The only problem is that the wall of the steerer is fairly thin, so the spoke just barely fits in there enough. I may try something like PVC with a thicker wall in the future.
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
divve wrote:Also, as tension becomes higher the chance of the spoke yielding from twisting increases.
If the spoke is yielding from twist *without* holding it, it will also yield if you are holding it on the bladed section. The stress that the spoke sees will be the same... same torque, same tensile load. The advantage of *not* holding is that you can easily see the amount of torque (twist) being applied to the spoke.
Maybe it is easier to use a holding tool rather than just overshoot... but I kinda doubt it since you are involving your other hand and have to fit the holder to the spoke.