Weight Weenies
http://weightweenies.starbike.com/forum/

Ritchey WCS C-260 stem... my quick review
http://weightweenies.starbike.com/forum/viewtopic.php?f=3&t=95427
Page 2 of 3

Author:  SL58 [ Tue Nov 01, 2011 3:16 am ]
Post subject:  Re: Ritchey WCS C-260 stem... my quick review

Thanks, Now only if they come up with -17deg.

Author:  Weenie [ Tue Nov 01, 2011 3:16 am ]
Post subject:  Re: Ritchey WCS C-260 stem... my quick review


Author:  Tenlegs [ Tue Nov 01, 2011 10:57 am ]
Post subject:  Re: Ritchey WCS C-260 stem... my quick review

Maybe there will be a -17deg version, but I need -17deg and 1-1/4, damn you Canyon.


http://www.bikeradar.com/news/article/r ... eek-30996/
"Ritchey will offer the new C260 in 80mm to 130mm lengths (in 10mm increments), with a flip-flop +/-6° angle. Versions will be available for both standard 1-1/8in steerers and the bigger 1-1/4in clamp size used by Canyon and now Giant (though the latter size will only mainly be available to OEMs for now). Riders needing a more aggressive position will get a -17° option as well."

Author:  sovereign [ Tue Jan 17, 2012 9:09 pm ]
Post subject:  Re: Ritchey WCS C-260 stem... my quick review

Quote:
"Ritchey claims the new C260 also passes the rigorous CEN testing standard and records fatigue lives three to four times longer than those of earlier forged models..."


http://www.bikeradar.com/news/article/ritcheys-new-100g-c260-stem-sneak-peek-30996/

And 30% stiffer, per the Ritchey site.

Any updates from C260 users? Is the increased stiffness noticeable for those who have used both a C260 and a 4-Axis? Any resolution to the finish cracking around the bolts?

I am considering a Ritchey stem for a 29er HT. The increased stiffness and strength make it a no brainer for this application. Unless, the 4-Axis is "good enough", as they are much cheaper.

Author:  velobob [ Sat Aug 25, 2012 2:41 pm ]
Post subject:  Re: Ritchey WCS C-260 stem... my quick review

I also have problems with the bolts. I tightened them to the 5NM using a torque wrench (the stem is going on my cyclocross bike so I wanted the most force possible) and when I went to try and remove them I could not - they started to strip.

anyone know where I could get some replacements??

Author:  tcsbutton [ Sat Aug 25, 2012 4:51 pm ]
Post subject:  Re: Ritchey WCS C-260 stem... my quick review

Contact Ritchey for some T-20 replacements.

Author:  Stockie [ Sat Aug 25, 2012 7:09 pm ]
Post subject:  Re: Ritchey WCS C-260 stem... my quick review

Why don't you replace the bolts with titanium?
That would bring the weight down to about 100 grams. That's is almost as light as an F99 stem (which is less stiff).

Author:  velobob [ Wed Sep 26, 2012 2:37 am ]
Post subject:  Re: Ritchey WCS C-260 stem... my quick review

thanks tcsbutton - the T-20 bolts work like a charm!!! the stem should just come with those stock

Author:  Rick [ Wed Sep 26, 2012 6:35 pm ]
Post subject:  Re: Ritchey WCS C-260 stem... my quick review

I switched from a 3T ARX Team stem with Easton EC90 SLX bars to a Ritchey WCS Carbon Curve bar with Ritchey C260 stem.

So I can't be sure if it is the bars or the stem, but the increase in stiffness was almost astounding. I am not a guy who worships stiffness, and I never felt like my old setup was "lacking stiffness". It always seemed perfectly fine. But as soon as I switched components my first reaction was "Wow! This makes my front end feel like it is cast concrete! The reason I switched was to get wider bars, which should be less stiff in theory. I went from 40 cm to 42 cm.
The stem change was just for aesthetics.

I didn't have any problem with the C260 bolts. Since they are smaller diameter I was being very careful and used my torque wrench, but went to the full 5 Nm

Author:  elfuinha [ Wed Sep 26, 2012 8:38 pm ]
Post subject:  Re: Ritchey WCS C-260 stem... my quick review

Can any one measure the length of the bolts, I'm thinking of buying the superlogic and change the bolts for Ti.
Best regards

Author:  sovereign [ Wed Sep 26, 2012 8:54 pm ]
Post subject:  Re: Ritchey WCS C-260 stem... my quick review

elfuinha wrote:
Can any one measure the length of the bolts, I'm thinking of buying the superlogic and change the bolts for Ti.
Best regards



OAL is ~19.25mm for the bolts on the C260 Carbon. Threaded portion is ~15mm. Measured with a digital caliper, on the bike (I did not remove a bolt due to not wanting to retention.)

Author:  elfuinha [ Wed Sep 26, 2012 10:04 pm ]
Post subject:  Re: Ritchey WCS C-260 stem... my quick review

M4x20mm?

Thanks

Author:  Rick [ Wed Sep 26, 2012 11:50 pm ]
Post subject:  Re: Ritchey WCS C-260 stem... my quick review

Bolt length is cited by the threaded portion only. So, mine are 15mm, and that also includes a ~1mm flat washer under the heads.

Author:  elfuinha [ Thu Sep 27, 2012 12:59 am ]
Post subject:  Re: Ritchey WCS C-260 stem... my quick review

Ok, M4x15mm
Bike hardest as them including de washers in black Ti, so that should solve
The softness of the steel bolt and should be lighter as well.

Thanks for the info, just have to wait until Nov / Dec.

Author:  eric01 [ Thu Sep 27, 2012 3:57 am ]
Post subject:  Re: Ritchey WCS C-260 stem... my quick review

Ti bolts are softer than steel no? If you are rounding the steel bolts, you'll round the Ti bolts too if I'm not mistaken

Author:  elfuinha [ Thu Sep 27, 2012 12:50 pm ]
Post subject:  Re: Ritchey WCS C-260 stem... my quick review

I don't think so. It depends on the titanium. 6/4 is very strong, see the bolts on the extralite they are M3 at handlebar, but all bolts in small sizes. You should always be extra careful, and use good tools.

Author:  Weenie [ Thu Sep 27, 2012 12:50 pm ]
Post subject:  Re: Ritchey WCS C-260 stem... my quick review


Page 2 of 3 All times are UTC+01:00
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/