Canyon Ultimate SLX 8.0 steerer plug adjustment
Moderator: robbosmans
Just got a Canyon Ultimate 8.0 SLX and I'm trying to figure out how to drop the steerer plug low enough to use the super long bolt for the top cap. Seems like it might be glued in there? There's a 5mm that loosens the center but plug itself won't budge.
Note that this is the 8.0 with standard stem & headset (not integrated bar/stem.)
TIA
Note that this is the 8.0 with standard stem & headset (not integrated bar/stem.)
TIA
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
Can you post a pic?
Will do so tonight, thanks - away from the bike ATM
I have the same bike and just cut the steerer 2 cm shorter. I was able to loosen off the 5mm Allen bolt and then carefully push the plug down 2 cm, using the same Allen key, then tighten up again, all ok.
I have sent an email query to canyon though, because I would like to see some technical information about the plug, particularly the optimal depth.
Sent from my iPhone using Tapatalk
I have sent an email query to canyon though, because I would like to see some technical information about the plug, particularly the optimal depth.
Sent from my iPhone using Tapatalk
Yep, Canyon said just to loosen the 5mm, thentap it down gently. You can adjust the height back up if it goes too low by simple leaving the 5mm loose and tightening via the top tap bolt, which will pull the plug upward.
I'm going to source a shorter top cap bolt, which should allow the plug to be at same height as both stem bolts.
I'm going to source a shorter top cap bolt, which should allow the plug to be at same height as both stem bolts.
gdnicoll wrote:I have the same bike and just cut the steerer 2 cm shorter. I was able to loosen off the 5mm Allen bolt and then carefully push the plug down 2 cm, using the same Allen key, then tighten up again, all ok.
I have sent an email query to canyon though, because I would like to see some technical information about the plug, particularly the optimal depth.
Sent from my iPhone using Tapatalk
Good tip for getting it out, was wondering about that!
Sent from my iPhone using Tapatalk
peterpen wrote:Yep, Canyon said just to loosen the 5mm, thentap it down gently. You can adjust the height back up if it goes too low by simple leaving the 5mm loose and tightening via the top tap bolt, which will pull the plug upward.
I'm going to source a shorter top cap bolt, which should allow the plug to be at same height as both stem bolts.
Sent from my iPhone using Tapatalk
Yes, 2016/17 model year. Cf slx 8.0 di2. The acros "the clamp" that was used on the previous model generation is no longer used. Now a much more typical headset. Also the headset bearings are no longer pressed into the head tube, they now lift out by hand. Hurrah.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
gdnicoll wrote:Yes, 2016/17 model year. Cf slx 8.0 di2. The acros "the clamp" that was used on the previous model generation is no longer used. Now a much more typical headset. Also the headset bearings are no longer pressed into the head tube, they now lift out by hand. Hurrah.
Sent from my iPhone using Tapatalk
Thanks for info.
I thought the headset cover (under the stem) on Ultimate 2016/17 has different shape (not round like Yours) but more oval.
I saw it here (on Canyon page):
Does Canyon provide different covers/spacers with Ultimate?
Whats size of Your frame and Your height also?
gdnicoll wrote:Good spotting and I can't explain the difference.
I have a medium frame, swapped the stem to 110 mm, and am 180 cm. A very good fit. Cheers.
Sent from my iPhone using Tapatalk
Size dillema here . I am 178cm with 83.5cm inseam. And as always.. between S and M size frame according to Canyon.
Cannot decide.
Do You know Your saddle height and Inseam?
Last edited by nonamed on Tue Jan 10, 2017 11:13 am, edited 1 time in total.
-
- Posts: 58
- Joined: Mon Jun 01, 2015 9:06 pm
nonamed wrote:gdnicoll wrote:Good spotting and I can't explain the difference.
I have a medium frame, swapped the stem to 110 mm, and am 180 cm. A very good fit. Cheers.
Sent from my iPhone using Tapatalk
Size dillema here . I am 178cm with 83.5cm inseam. And as always.. between S and M size frame according to Canyon.
Cannot decide.
My dad is the same. He rides M.
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com