HOT: Active* forum members generally gain 5% discount at starbike.com store!
Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Blog NEW Articles FAQ Contact About




Post new topic Reply to topic  [ 20 posts ] 
Go to page Previous  1, 2
Author Message
PostPosted: Thu May 29, 2014 7:12 am 
Offline

Joined: Mon May 12, 2014 9:42 am
Posts: 10
nlouthan wrote:
Post a pic of the frame and/or the BB, then there will be no confusion on our part regarding what you have. Also, what does it say on the BB? Wilier labels everything.

Image
The measurement is in mm, threads inside?
Width of the BB housing measures 93.02mm, outerside to outerside.

Sended from my SingleSideBand Sony Xperia


Top
 Profile  
 
PostPosted: Thu May 29, 2014 7:23 am 
Offline

Joined: Mon May 12, 2014 9:42 am
Posts: 10
Image
Image




Sended from my SingleSideBand Sony Xperia


Top
 Profile  
 
Posted: Thu May 29, 2014 7:23 am 


Top
  
 
PostPosted: Thu May 29, 2014 9:26 am 
Offline

Joined: Fri Jun 25, 2004 8:32 pm
Posts: 1306
Location: the Netherlands
Looks like a Willier with BB94.

Campa/Fulcrum crankset will fit since Willier delivers them with these

and they deliver their frameset with something like this:

http://www.twohubs.com/Product/wilier/wilier-bottom-bracket-bearing-kit/712387#.U4buWCgnjCs


Top
 Profile  
 
PostPosted: Thu May 29, 2014 2:18 pm 
Offline

Joined: Mon Jan 31, 2011 2:41 am
Posts: 103
Location: SF Bay Area
On the DS, there should be two holes on the very outside edge of the BB at 3 and 9 o'clock if looking at the BB from the side. That's where the snap ring ends go in. It goes on from the bottom. I use a pick to grab the snap ring and pull it into place. The cranks slide straight in without any spacers. Have you tried this? You might have to wiggle them if you're not pushing straight. Note that no tools are needed for pushing the cranks in. Be sure to try and pull the DS half out after you install the snap ring to make you you have it in the correct place. It slides in further than you might think. On the NDS, you'll need the wavy washer for taking up slack. Then torque down the center bolt and you're done. It is truly a two minute job.

The black plastic spacers from the link above are to run a Shimano or SRAM crank and are not needed with Campy Ultra Torque.

Not sure why there are threads on the inner most part of the BB, but you don't need them.


Top
 Profile  
 
PostPosted: Thu May 29, 2014 3:26 pm 
Offline

Joined: Mon May 12, 2014 9:42 am
Posts: 10
nlouthan wrote:
On the DS, there should be two holes on the very outside edge of the BB at 3 and 9 o'clock if looking at the BB from the side. That's where the snap ring ends go in. It goes on from the bottom. I use a pick to grab the snap ring and pull it into place. The cranks slide straight in without any spacers. Have you tried this? You might have to wiggle them if you're not pushing straight. Note that no tools are needed for pushing the cranks in. Be sure to try and pull the DS half out after you install the snap ring to make you you have it in the correct place. It slides in further than you might think. On the NDS, you'll need the wavy washer for taking up slack. Then torque down the center bolt and you're done. It is truly a two minute job.

The black plastic spacers from the link above are to run a Shimano or SRAM crank and are not needed with Campy Ultra Torque.

Not sure why there are threads on the inner most part of the BB, but you don't need them.


Hi and thank You very much for answering, there is no visible holes on the BB, I tried to locate them underneath the black paint. The outer part of the BB DS is all solid substance without holes. I mailed the dealer in Holland, hoping I could get some sollution for this matter. Fortunatelly I have Izoard so I'm not totally without bike.
Brgds, Björn


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 20 posts ] 
Go to page Previous  1, 2


Who is online

Users browsing this forum: 9734344, albertop07, cyclenutnz, Google Adsense [Bot], jimtbaker, kookie, NickD51, uraqt and 38 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. Wilier Cento 1 Air Weight

in Road

vision646

4

488

Sun May 10, 2015 7:38 pm

vision646 View the latest post

There are no new unread posts for this topic. What to replace my Wilier Cento Uno?

in Road

Fourthbook

12

680

Tue Aug 25, 2015 6:25 pm

Fourthbook View the latest post

There are no new unread posts for this topic. Advice for EPS newbie

in Road

liam7020

8

640

Sun Jul 12, 2015 1:12 pm

liam7020 View the latest post

There are no new unread posts for this topic. 2011 Wilier Cento Uno Measurement

in Road

rgamble

0

89

Tue Jun 30, 2015 5:22 pm

rgamble View the latest post

There are no new unread posts for this topic. BMC SLR 01 2013 DI2 Version need help!

in Road

MARLON

10

1024

Tue Jun 02, 2015 5:58 pm

aussietim View the latest post


It is currently Sun Aug 30, 2015 12:34 am

All times are UTC + 1 hour




Advertising   –  FAQ   –  Contact   –  Convert   –  About

© Weight Weenies 2000-2013
hosted by starbike.com


How to get rid of these ads? Just register!


Powered by phpBB