Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Blog NEW Galleries NEW FAQ Contact About Impressum
It is currently Tue Jun 27, 2017 10:17 am

All times are UTC+01:00





Post new topic  Reply to topic  [ 8 posts ] 
Author Message
PostPosted: Tue Dec 24, 2013 5:59 am 
Offline

Joined: Wed Nov 21, 2012 3:05 am
Posts: 283
i had my LBS change the bearing to the ceramic bearing set that i bought from fairwheel and ever since changing the bearings the tension on the free wheel has been to tight and have gone back to the LBS 3 different times do see about making it spin easy. While i am riding the chain is flopping on the chainstay and scratching up the drive side chain stay. I have looked at it and cannot figure it out. It will work for a little bit and then i stop peddling and the cassette just keeps turning and the chain starts hitting the spokes and it is really frustrating. i do not have bearing presses that is why i took it to my LBS. What do you recommend? thanks


Top
   
PostPosted: Tue Dec 24, 2013 7:27 am 
Offline

Joined: Fri Jun 05, 2009 9:40 am
Posts: 570
Location: Switzerland
back to the shop (again)


Top
   
Posted: Tue Dec 24, 2013 7:27 am 


Top
   
 
PostPosted: Tue Dec 24, 2013 9:14 am 
Offline
User avatar

Joined: Tue Jan 23, 2007 11:22 am
Posts: 3657
Location: Leg hurty
Too much lube or the wrong type of lube on the freehub body teeth.
Sounds like the freehub body has been greased. If it's cold it'll be even worse.
Try bringing it into the warm, if it's better at room temperature you have a lube issue.
Just wipe it out and run some oil on the pawls instead.

_________________
Pedalling Law Student.


Top
   
PostPosted: Tue Dec 24, 2013 11:27 am 
Offline

Joined: Wed Nov 21, 2012 3:05 am
Posts: 283
there is grease on, i will try oil and see if that helps


Top
   
PostPosted: Tue Dec 24, 2013 3:06 pm 
Offline

Joined: Mon Jan 24, 2011 8:09 pm
Posts: 921
Right, the thick grease is causing this likely. Clean it out good with a synthetic motor oil/light lubricant, wipe it all down well, remove the pawls themselves if possible and clean it real well. Pawls can go flying if you aren't careful along with the metal springs.

Once cleaned real well, put the pawls/springs back together, right before the hub shell goes on over the pawls, put 1-2 small drops of low viscosity lubricant, again, like a synthetic motor oil, on each pawl. Re-assemble the free hub body back on, re-tighten.

Spin the wheel in your hands and ensure it spins smoothly and doesn't catch. Report back!


Top
   
PostPosted: Thu Dec 26, 2013 4:25 am 
Offline

Joined: Wed Nov 21, 2012 3:05 am
Posts: 283
Well all i had was real oil but want to say thanks for the info. I put oil on it and have put on 80 miles and the problem is gone. I want to know how long you do you think I have before I need to change the oil? Do you know of one syn oil better than the others? Thanks again


Top
   
PostPosted: Thu Dec 26, 2013 10:32 am 
Offline
User avatar

Joined: Tue Jan 23, 2007 11:22 am
Posts: 3657
Location: Leg hurty
Depends on your local conditions really? At this time of year the wet here in the UK can really get into everything.
A little bit of water can mix with mineral oil and turn it into a nasty sludge that doesn't lubricate very well and will let your steel parts corrode.
I use wet chain lube on mine, as it's nice and runny, synthetic and it sticks to your pawls etc.
Could be worth looking for a softer grease if you want to fit and forget instead of lubing on every service?
Glad you're sorted out though as it's annoying when you have to keep going to a shop to get stuff like that looked at.
Well done, and Happy Christmas. :thumbup: :beerchug:

_________________
Pedalling Law Student.


Top
   
Posted: Thu Dec 26, 2013 10:32 am 


Top
   
 
PostPosted: Thu Dec 26, 2013 2:23 pm 
Offline

Joined: Wed Nov 21, 2012 3:05 am
Posts: 283
I live in dry dusty so cal, USA. It only rains a couple weeks a year. I will get some better oils going forward and thanks again for the info. Happy holidays to you too.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 8 posts ] 

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. Etap problems

in Road

Jase46

10

1493

Wed Feb 01, 2017 4:23 am

moonoi View the latest post

There are no new unread posts for this topic. Campy drive train problems

in Road

DeLuz

13

760

Mon May 22, 2017 7:13 pm

2lo8 View the latest post

There are no new unread posts for this topic. Dura Ace 7700 rear mech problems

in Road

Penthousepete

3

295

Tue Aug 09, 2016 9:21 pm

Asteroid View the latest post

There are no new unread posts for this topic. ST-RS685 Hood Problems (shimano ultra hydraulic disc)

in Road

theyoungconnoisseur

7

686

Tue Jan 24, 2017 11:32 pm

MichaelB View the latest post


All times are UTC+01:00


Who is online

Users browsing this forum: Flasher, nesfyl, shipley, veskox, Yahoo [Bot] and 38 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited