HOT: Active* forum members generally gain 5% discount at starbike.com store!
Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Blog NEW Articles FAQ Contact About




Post new topic Reply to topic  [ 9 posts ] 
Author Message
PostPosted: Wed Aug 14, 2013 4:03 pm 
Offline
Administrator
User avatar

Joined: Sat Jun 19, 2004 11:08 am
Posts: 6289
Location: Urbana, Illinois
I usually only use the left shifter once or twice during a ride. This morning I went to shift into the big ring and after I left go it shifted right back into the small ring. The detents on the shifter were not catching. After trying a bunch of times I have one of the detents back. I'm using the Goretex cables which are know to peal. I need to look at it later but I suspect its pieces of the cable coating that I'm going to need to clean out of the shifter.

Anybody else ever had this issue or any other thoughts on this?

_________________
RESIDENT GRUMPY OLD MAN.


Top
 Profile  
 
Posted: Wed Aug 14, 2013 4:03 pm 


Top
  
 
PostPosted: Wed Aug 14, 2013 5:06 pm 
Offline

Joined: Tue Feb 05, 2013 8:29 pm
Posts: 236
Make sure your cable doesn't have too much tension in it.


Top
 Profile  
 
PostPosted: Wed Aug 14, 2013 8:31 pm 
Offline
Formerly known as PezTech
User avatar

Joined: Tue Sep 26, 2006 12:37 am
Posts: 5701
Location: Phoenix Arizona
yep. tension and junk can do it. should "develope" that problem though. I would read run the front mech cable. free it completely, operate the lever a few times to get any junk out and then run a new cable.

_________________
charles@pezcyclingnews.com


Top
 Profile  
 
PostPosted: Wed Aug 14, 2013 8:51 pm 
Offline

Joined: Wed Feb 16, 2011 7:46 pm
Posts: 170
i'm having a slightly different issue. i have the 2013 levers - and the paddle on my left shifter seems loose. lots of play. it wiggles everywhere. seems sloppy. 'zero loss' doesn't seem very accurate in my case as i have to throw the leaver quite far to shift to the big ring. down shifting is no prob. is there a way to tighten it up?


Top
 Profile  
 
PostPosted: Wed Aug 14, 2013 8:56 pm 
Offline

Joined: Tue Feb 05, 2013 8:29 pm
Posts: 236
Zero-loss means that the paddle starts moving the derailleur with no dead space. You still have to move it all the way over to get a full upshift, but you have no "dead movement" like on Shimano, Campy, and lower Sram components where you can wiggle the paddle without affecting the cable/derailleur at all.

If you are able to move your left paddle while the chain is in the small ring, and you can do it without getting any resistance or moving the cable, something is VERY wrong.


Top
 Profile  
 
PostPosted: Thu Aug 15, 2013 9:39 am 
Offline
Administrator
User avatar

Joined: Sat Jun 19, 2004 11:08 am
Posts: 6289
Location: Urbana, Illinois
I get home last evening and put the bike on the stand ready to get some work done. The bike repeatedly shifted perfect. :? Today's training ride will tell the story. If all goes well I will change the cable anyway this weekend since I do not want a repeat issue with this.

_________________
RESIDENT GRUMPY OLD MAN.


Top
 Profile  
 
PostPosted: Thu Aug 15, 2013 5:08 pm 
Offline
Moderator
User avatar

Joined: Fri Dec 10, 2004 10:22 am
Posts: 3684
Location: Washington, DC
I hate it when I cannot repeat the issue when home. This is quite annoying and happens more often than not...

_________________
Cervelo R3, Campagnolo Chorus/Record mix... pastatrails.blogspot.com
And you can call me Macktastik Honey Pete Kicks, thank you.


Top
 Profile  
 
PostPosted: Thu Aug 15, 2013 7:32 pm 
Offline

Joined: Wed Feb 16, 2011 7:46 pm
Posts: 170
juanmoretime - i hope your issue has resolved itself.

I am not so lucky. Turns out something is VERY wrong.

pic:
Image

note the cracked piece in there. it still works... just sloppy as i described above.


Top
 Profile  
 
PostPosted: Fri Aug 16, 2013 2:18 am 
Offline
Administrator
User avatar

Joined: Sat Jun 19, 2004 11:08 am
Posts: 6289
Location: Urbana, Illinois
Worked flawlessly on this mornings ride. I wll replace the cable this weekend.

_________________
RESIDENT GRUMPY OLD MAN.


Top
 Profile  
 
Posted: Fri Aug 16, 2013 2:18 am 


Top
  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 9 posts ] 


Who is online

Users browsing this forum: Bing [Bot], Geoff, glepore, hilts, LionelB, RC856, zulu695 and 27 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. Shimano Dura Ace 9000 Shifter Issue (& 6800 cassette moan)

in Road

dynaserve

7

1772

Fri Apr 25, 2014 7:46 pm

n808 View the latest post

There are no new unread posts for this topic. di2 sprint shifter alternative

in Road

grouk

13

703

Fri Oct 10, 2014 10:56 pm

grouk View the latest post

There are no new unread posts for this topic. Di2 Shifter/Brake Assembly

in Road

ironman1

0

262

Fri Sep 26, 2014 5:05 pm

ironman1 View the latest post

There are no new unread posts for this topic. Do I need a new shifter (more Campag woes)?

in Road

Lewis

10

691

Fri Jun 27, 2014 10:10 pm

bikerjulio View the latest post

There are no new unread posts for this topic. Felt shifter hoods?

in Road

Lucas1234

1

472

Tue Jan 21, 2014 12:34 pm

theremery View the latest post


It is currently Thu Dec 18, 2014 3:05 pm

All times are UTC + 1 hour




Advertising   –  FAQ   –  Contact   –  Convert   –  About

© Weight Weenies 2000-2013
hosted by starbike.com


How to get rid of these ads? Just register!


Powered by phpBB