Page 1 of 2
Question about Rotor3D+ (P2M) (110BCD) and Osymetric
Posted: Mon Mar 18, 2013 8:11 pm
by lyot
Dear all,
Does anyone know whether a Rotor 3D+ crankset that has a Power2Max installed, can be outfitted with a Osymetric chainset (110BCD)? I just came to the conclusion that the Rotor Q Rings XL that I ordered do not fit, at least not the outer ring. For the time being, I'm not yet willing to take it to the next level with the Rotor Q Rings and to use the dremel. Any input on whether Oysemtric rings would fit would be helpful.
These won't fit :
Would these fit ?
Not yet ready to do this with my Q Ring XL, as seen on slowtwitch, as Power2Max says it should be 'avoided' ..
From the homework done by the individual on slowtwitch, I would believe that the Osyemtrics might be just about right?
Re: Question about Rotor3D+ (P2M) (110BCD) and Osymetric
Posted: Tue Mar 19, 2013 6:14 pm
by lyot
I've obtained an answer through Power2Max, and they let me know that the Osymetrics 110 BCD should fit the Rotor 3D+ Powermax
Re: Question about Rotor3D+ (P2M) (110BCD) and Osymetric
Posted: Tue Mar 19, 2013 6:14 pm
by Weenie
Visit
starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
Re: Question about Rotor3D+ (P2M) (110BCD) and Osymetric
Posted: Wed Mar 20, 2013 7:10 pm
by sastre
i asked them this same question and the response was 130mm osymetric only which was upsetting but now im not sure. but now im thinking about praxis 52/36 but i like the osy a lot.
Re: Question about Rotor3D+ (P2M) (110BCD) and Osymetric
Posted: Wed Mar 20, 2013 8:16 pm
by lyot
sastre wrote:i asked them this same question and the response was 130mm osymetric only which was upsetting but now im not sure. but now im thinking about praxis 52/36 but i like the osy a lot.
I'll have an answer for you within a week, I hope. I ordered the 110 BCD Osymetric. I'll post the result here
Re: Question about Rotor3D+ (P2M) (110BCD) and Osymetric
Posted: Wed Mar 20, 2013 11:04 pm
by sastre
this is a 130
Re: Question about Rotor3D+ (P2M) (110BCD) and Osymetric
Posted: Thu Mar 21, 2013 10:15 am
by jever98
Hi all,
Nicolas here from power2max. I am happy to confirm that you can mount 110BCD Osymetric rings without problems. The reason the 110BCD Aero Q-Rings don't work is that they interfere with the battery cover. The Osymetrics are cut out in that area, so no problem there. A training buddy of mine uses both the compact and the 130BCD version, I run the 130 BCD on my TT bike
I hope this helps,
Best wishes
Nicolas
power2max
Re: Question about Rotor3D+ (P2M) (110BCD) and Osymetric
Posted: Thu Mar 21, 2013 6:55 pm
by lyot
Allright, thanks for clarifying Nicolas ! I'll post a picture once it's mounted.. To be sure, the cut out area is the one that needs to go underneath the battery cover, right ?
Re: Question about Rotor3D+ (P2M) (110BCD) and Osymetric
Posted: Thu Mar 21, 2013 7:02 pm
by jever98
@lyot: that's right. Enjoy your power2max and osymetrics!
Sent from my HTC One X using Tapatalk 2
Re: Question about Rotor3D+ (P2M) (110BCD) and Osymetric
Posted: Fri Mar 22, 2013 11:23 pm
by DrGalactus
Thanks for the reply Nicolas, had been wondering this myself, time to break out the credit card I guess
Re: Question about Rotor3D+ (P2M) (110BCD) and Osymetric
Posted: Sat Mar 23, 2013 4:50 pm
by lyot
Hallelujah, succes !
It's not the cut out area though that needs to go underneath the battery holder. It's the opposite part of the ring
Re: Question about Rotor3D+ (P2M) (110BCD) and Osymetric
Posted: Sun Mar 24, 2013 7:40 pm
by jever98
Sorry lyot, I misunderstood what you meant with cutout.
Enjoy your new p2m
!
Re: Question about Rotor3D+ (P2M) (110BCD) and Osymetric
Posted: Mon Mar 25, 2013 7:38 pm
by sastre
this is top new's think i no what's next on the list
a tip for you if you would like to remove the osymetric graphic from the chainrings park chain degreaser rub it on
use it a couple of times and hey presto blacked out
Re: Question about Rotor3D+ (P2M) (110BCD) and Osymetric
Posted: Mon Mar 25, 2013 9:19 pm
by lyot
Thanks for the tip ! I'll let it on for a while, but probably will remove it within a couple of weeks/months.. A bit too white, indeed !
Re: Question about Rotor3D+ (P2M) (110BCD) and Osymetric
Posted: Thu Mar 28, 2013 6:24 am
by 54x11
Does anyone know if you can fit the Power2Max meter to the Rotor Flow crankset? I had a search around but couldn't find an answer.
Re: Question about Rotor3D+ (P2M) (110BCD) and Osymetric
Posted: Thu Mar 28, 2013 6:24 am
by Weenie
Visit
starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
Re: Question about Rotor3D+ (P2M) (110BCD) and Osymetric
Posted: Thu Mar 28, 2013 12:24 pm
by jever98
54x11 wrote:Does anyone know if you can fit the Power2Max meter to the Rotor Flow crankset? I had a search around but couldn't find an answer.
Hi 54x11,
yup, fits the 3D+ model.
Best
Nicolas