Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Blog NEW Galleries NEW FAQ Contact About
It is currently Tue May 24, 2016 10:37 pm
Recently the board software has been updated and there are some known bugs/failures:
- Avatars are currently not being displayed ✔ FIXED
- Tapatalk connection is currently broken ✔ FIXED

If you find more errors please post it here: http://weightweenies.starbike.com/forum/viewtopic.php?f=7&t=139062


All times are UTC+01:00





Post new topic  Reply to topic  [ 6 posts ] 
Author Message
 Post subject: Nokon cable refurbish
PostPosted: Sat Oct 27, 2012 12:13 am 
Offline

Joined: Mon Aug 02, 2010 2:06 am
Posts: 2
I am refurbishing my Nokon cable system and looking for input on best cable’s and liners to use. I have Shimano Dura 7800 shifters and routing shift cables under the bar tape. To add also I have the adaptor kit that will make the routing under the tape easier. I am using the standard nokon parts right now


Top
   
PostPosted: Sat Oct 27, 2012 5:35 am 
Offline

Joined: Sun Apr 15, 2012 7:04 pm
Posts: 27
I'm using the same nokon + DA7800 setup as you but can you show me a picture of the adaptor kit you are using?

Thanks


Top
   
PostPosted: Sat Oct 27, 2012 8:52 am 
Offline

Joined: Fri Dec 24, 2010 9:37 pm
Posts: 809
Location: it's raining, it must be uk
liner - the powercordz liner is good with their cables, but also i've used it with steel cables and find it just as good with them

the nokon liner is tighter, i've used it but found over time it deformed slightly at the joints between segments and the drag increased, i've not had that problem with the powercordz liner


Top
   
PostPosted: Sun Oct 28, 2012 2:49 am 
Offline

Joined: Mon Aug 02, 2010 2:06 am
Posts: 2
The adaptor kit is real simple it is approximately 46 small pearls just like the ones use to make the bend @ the rear, also included in the kit is a new set of liners. They are listed on the Nokon web site. I could not find them on line so I called up the US distributor and ordered them over the phone. As for the liners I used power cordz liner last time I did this and it deformed and caused waves and slowed my shifts down. I could get it to work fine on the stand but after a few miles on the road I had slow shits again. The Power cordz liner I used then was blue. The latest liner I received from Power Cordz is clear with a green strip in it. One last note on the liners. I saw Jagwire liners in my local shop that stated on the lable compatibility with Nokon outers and they look identical to the one's Power Cordz sent me that are branded Power Cordz.


Top
   
PostPosted: Sun Oct 28, 2012 2:52 am 
Offline

Joined: Sun Apr 01, 2007 10:50 pm
Posts: 199
WW08012010 wrote:
The adaptor kit is real simple it is approximately 46 small pearls just like the ones use to make the bend @ the rear, also included in the kit is a new set of liners. They are listed on the Nokon web site. I could not find them on line so I called up the US distributor and ordered them over the phone. As for the liners I used power cordz liner last time I did this and it deformed and caused waves and slowed my shifts down. I could get it to work fine on the stand but after a few miles on the road I had slow shits again. The Power cordz liner I used then was blue. The latest liner I received from Power Cordz is clear with a green strip in it. One last note on the liners. I saw Jagwire liners in my local shop that stated on the lable compatibility with Nokon outers and they look identical to the one's Power Cordz sent me that are branded Power Cordz.


:shock: :shock: :shock:

You might want to see a doctor for that...

_________________
GRAVELBIKE.COM - ride everything


Top
   
PostPosted: Sun Oct 28, 2012 4:05 pm 
Offline

Joined: Mon Aug 16, 2010 6:43 pm
Posts: 438
Location: Canada
Depending what is around at the shop I either use Shimano or Jagwire housing to get my liners.. It's easy enough to peel the outer sheath with a sharp knife and remove the stainless strands. Then you are left with the internal liner to thread your Nokon on to.



Also you should use the search feature of the forum. It's topic comes up regularly... :smartass:

_________________
Flickr
Tarmac SL3 Project Yellow
Follow on Instagram


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 6 posts ] 

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. Attachment(s) advice on a build - Marinoni Ciclo refurbish project

in Road

ethnik

11

488

Fri May 06, 2016 12:05 pm

tigoose View the latest post

There are no new unread posts for this topic. lightweight cable set

[ Go to page: 1 2 3 ]

in Road

addictR1

30

2496

Tue Jan 05, 2016 3:47 am

AlphaDogCycling View the latest post

There are no new unread posts for this topic. Di2 cable lengths

in Road

jano

6

570

Tue Jul 14, 2015 7:50 pm

jano View the latest post

There are no new unread posts for this topic. Cable rattle...

in Road

Devon

12

591

Tue Dec 15, 2015 9:20 am

Devon View the latest post

There are no new unread posts for this topic. Cable issues Cervelo S2.

in Road

alpinestar

8

375

Wed Apr 06, 2016 3:28 pm

nickcube View the latest post


All times are UTC+01:00


Who is online

Users browsing this forum: CanadianBiker, MSNbot Media and 20 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited