Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Blog NEW Galleries NEW FAQ Contact About
It is currently Sat Jun 25, 2016 11:43 am
Recently the board software has been updated and there are some known bugs/failures:
- Avatars are currently not being displayed ✔ FIXED
- Tapatalk connection is currently broken ✔ FIXED
- Avatars cannot be uploaded ✔ FIXED

Please note that we will soon do some changes in WW board template design in case to get a fully mobile/desktop responsiveness board!
If you find more errors please post it here: http://weightweenies.starbike.com/forum/viewtopic.php?f=7&t=139062


All times are UTC+01:00





Post new topic  Reply to topic  [ 5 posts ] 
Author Message
PostPosted: Tue Aug 07, 2012 3:39 pm 
Offline

Joined: Tue Apr 05, 2011 7:41 pm
Posts: 630
Hi all , i have a cerevelo s1 with funda pro fork, carbon steerer , alu sleeve inside, the alu sleeve slips up when tightening headet. Any remedy out there? frame purchased in april so warrantied i guess but shiuld this happen? Epoxy in the steerer do it? Cheers...


Top
   
PostPosted: Tue Aug 07, 2012 3:47 pm 
Offline

Joined: Fri Jun 05, 2009 9:40 am
Posts: 551
Location: Switzerland
Monkeyboy3333 wrote:
Hi all , i have a cerevelo s1 with funda pro fork, carbon steerer , alu sleeve inside, the alu sleeve slips up when tightening headet. Any remedy out there? frame purchased in april so warrantied i guess but shiuld this happen? Epoxy in the steerer do it? Cheers...


not quite clear, did you glue (epoxy) the sleeve, or did you not

it is a must to glue it in


Top
   
PostPosted: Tue Aug 07, 2012 5:18 pm 
Offline

Joined: Mon Mar 14, 2011 10:59 am
Posts: 348
Location: Oxfordshire UK
I never bothered using the alu insert in my Funda forks. I ran for 2 years without it with no problems. However I did use a tall compression adjuster to preload the headset bearings:

http://www.chainreactioncycles.com/Mode ... fAodYBYAFg

Once the bearing preload was set and the stem clamped up tight, I removed the BBB and installed a Carbon-Ti X-Plug and X-Cap

_________________
Scott CR1SL 6.25Kg | CAAD10 6.56Kg


Top
   
PostPosted: Tue Aug 07, 2012 7:39 pm 
Offline

Joined: Sun May 21, 2006 3:06 am
Posts: 234
If it hasn't been epoxied in to begin with, do that. A sachet of the right compound is available as a spare part from 3T if it's missing.

I would use this system in every carbon fork I possible could. It supports the steerer far better than a conventional compressor and puts no outward pressure on the carbon steerer tube. The only downside is difficulty in trimming the fork down the track should you reduce your stack height.


Top
   
PostPosted: Tue Aug 07, 2012 10:38 pm 
Offline

Joined: Mon Mar 26, 2012 2:45 pm
Posts: 113
Location: Bali, Indonesia
If the 3T glue packet is unavailable, Dev Con 2 ton epoxy works fine for this purpose. The ID of the fork should be sanded lightly with 240ish paper, then it and the sleeve cleaned with rubbing alcohol prior to applying the epoxy. Place the fork upside down and allow the epoxy to cure.

Monkeyburger

_________________
...finding my inner Onoda-kun...


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 5 posts ] 

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. supersix himod bb sleeve ??

in Road

Dennistwowheels

13

833

Mon Dec 07, 2015 11:49 am

jorisee01 View the latest post

There are no new unread posts for this topic. DA BB86 bottom bracket : plastic sleeve needed?

in Road

Delorre

3

300

Tue Jul 28, 2015 8:26 pm

Delorre View the latest post

There are no new unread posts for this topic. Enve 2.0 Fork

[ Go to page: 1 2 ]

in Road

beatle

17

1209

Sun Jan 10, 2016 1:32 pm

beatle View the latest post

There are no new unread posts for this topic. What Disc Fork?

in Road

Valbrona

3

293

Sat May 07, 2016 12:48 am

jrobart View the latest post

There are no new unread posts for this topic. Recomendation for fork?

in Road

Svetty

3

284

Mon Jan 25, 2016 3:03 pm

Svetty View the latest post


All times are UTC+01:00


Who is online

Users browsing this forum: Bing [Bot], TomColnago, Yahoo [Bot] and 15 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited