Page 1 of 2
Dogma 2 Electronic BB shell
Posted: Sun Jun 10, 2012 4:38 am
by ParisCarbon
If anyone has a Dogma2 Electronic would you be able to tell me if there is anyway to mount an SRM cadence sensor under there without gluing (ie is there a threaded screw hole for a traditional cable guide) Picture would be nice too if you could!
Many thanks in advance!
Dogma 2 Electronic BB shell
Posted: Sun Jun 10, 2012 4:38 am
by Weenie
Visit
starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
Re: Dogma 2 Electronic BB shell
Posted: Sun Jun 10, 2012 6:21 am
by bearsdidit
We have used the stock SRM style mount but used double sided tape. It sounds pretty hokey but it's secure.
Re: Dogma 2 Electronic BB shell
Posted: Sun Jun 10, 2012 10:58 am
by RobyDogma
Have used double sided tape on my dogma for 6 months without any problems, go for it!
/Roberto
Re: Dogma 2 Electronic BB shell
Posted: Sun Jun 10, 2012 1:06 pm
by ParisCarbon
Thanks guys... just exploring some options.... another site I found recommended 3M Marine Sealant as well..
Did you guys just use plain old double sided tape then?? Nothing extreme??
Sv: Dogma 2 Electronic BB shell
Posted: Sun Jun 10, 2012 1:16 pm
by RobyDogma
Yupp!
Nothing special just standard tape.
Skickat från min GT-I9100 via Tapatalk 2
Re: Dogma 2 Electronic BB shell
Posted: Sun Jun 10, 2012 1:47 pm
by ParisCarbon
Thanks!!!
Re: Dogma 2 Electronic BB shell
Posted: Sun Jun 10, 2012 1:48 pm
by RobyDogma
No problems
Re: Dogma 2 Electronic BB shell
Posted: Sun Jun 10, 2012 2:54 pm
by maxxevv
If you want peace of mind, can always opt for the 3M VHB tape. Look for the "outdoors" application version that's grey in colour.
I used it to glue the normal cadence sensor to my crank. Has held for the past 4 years!
Re: Dogma 2 Electronic BB shell
Posted: Sun Jun 10, 2012 4:32 pm
by Geoff
Why would you not toss the SRM thing and just glue-on a rare-earth magnet to the frame?
Re: Dogma 2 Electronic BB shell
Posted: Sun Jun 10, 2012 5:04 pm
by ParisCarbon
Saw the 3M tape as well in a search.
I don't want to glue personally.. but thats just me... it is a valid option though!
Just tossing around a build right now and looking at how much the bank account would suffer!!
Re: Dogma 2 Electronic BB shell
Posted: Mon Jun 11, 2012 2:54 pm
by MoreRideTime
I remember seeing a photo of Wiggin's time trial bike a while back. It showed a rare earth magnet glued to the down tube for the SRM. Looked to be a very clean setup. Here's the photo:
Re: Dogma 2 Electronic BB shell
Posted: Mon Jun 11, 2012 5:12 pm
by ParisCarbon
Hmm that with the 3M tape would be even better....
Re: Dogma 2 Electronic BB shell
Posted: Tue Jun 12, 2012 12:41 am
by Geoff
No, it wouldn't.
If you don't want to have any glue residue on the frameset, just steal your wife/gf's hot glue gun and use that. Make sure you have a good bit of a 'bead' around the magnet and it will stay-put just fine. It will come-off without any affect to your frameset.
Re: Dogma 2 Electronic BB shell
Posted: Tue Jun 12, 2012 2:21 am
by maxxevv
Geoff wrote:No, it wouldn't.
If you don't want to have any glue residue on the frameset, just steal your wife/gf's hot glue gun and use that. Make sure you have a good bit of a 'bead' around the magnet and it will stay-put just fine. It will come-off without any affect to your frameset.
Sounds like you have not used VHB tape before ??
Re: Dogma 2 Electronic BB shell
Posted: Tue Jun 12, 2012 2:21 am
by Weenie
Visit
starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
Re: Dogma 2 Electronic BB shell
Posted: Tue Jun 12, 2012 3:39 am
by Geoff
The VHB tape is too sticky. You need to be able to glue-on the magnet, test it and reposition it, if necessary...