Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Blog NEW Galleries NEW FAQ Contact About Impressum
It is currently Wed Dec 07, 2016 11:55 am
Recently the board software has been updated and there are some known bugs/failures:
- Avatars are currently not being displayed ✔ FIXED
- Tapatalk connection is currently broken ✔ FIXED
- Avatars cannot be uploaded ✔ FIXED

Please note that we will soon do some changes in WW board template design in case to get a fully mobile/desktop responsiveness board!
If you find more errors please post it here: http://weightweenies.starbike.com/forum/viewtopic.php?f=7&t=139062


All times are UTC+01:00





Post new topic  Reply to topic  [ 8 posts ] 
Author Message
 Post subject: LOOK 695 ZED2 CRANK BB
PostPosted: Sun May 27, 2012 3:42 pm 
Offline

Joined: Tue Mar 22, 2011 5:25 pm
Posts: 7
I bought a new 695 iPack 2011. After every ride my bb is a bit loose. The LBS tightens the non drive side again and then it just happens again. I was told a must put "loctite" on. Could somebody help perhaps ? mgouws@um.co.za


Top
   
 Post subject: LOOK 695 ZED2 CRANK BB
Posted: Sun May 27, 2012 3:42 pm 


Top
   
 
PostPosted: Mon May 28, 2012 10:13 am 
Offline

Joined: Thu Oct 14, 2010 7:13 am
Posts: 16
Location: Dubai - UAE
monre wrote:
I bought a new 695 iPack 2011. After every ride my bb is a bit loose. The LBS tightens the non drive side again and then it just happens again. I was told a must put "loctite" on. Could somebody help perhaps ? mgouws@um.co.za



on the non drive, there a black round that you can tight a bit. once screwed, it shouldn't move at all...
be sure you pushed well on the drive side.

_________________
========================

LOOK 695SR - DI2 - CORIMA AERO MCC/ZIPP 808
10 000km in the sand of Dubai... Hilly roads of RIO de JANEIRO and Mont VENTOUX in France


Top
   
PostPosted: Tue May 29, 2012 10:18 am 
Offline

Joined: Sun Oct 19, 2008 12:40 pm
Posts: 291
Location: England
Ptfe plumbers tape is your answer.....
I had to do mine along with the chainring bolts on my SR version.
God it's rigid!!!!
Hope this helps.


Top
   
PostPosted: Tue May 29, 2012 7:13 pm 
Offline

Joined: Tue Mar 22, 2011 5:25 pm
Posts: 7
Did you put the plumbers tape on the thread on the non drive side before tightening the lock ring ?


Top
   
PostPosted: Tue May 29, 2012 7:20 pm 
Offline

Joined: Sun Oct 19, 2008 12:40 pm
Posts: 291
Location: England
I did yes.....
Put a 4-5 layers around the threads....


Top
   
PostPosted: Tue May 29, 2012 8:49 pm 
Offline

Joined: Wed Mar 16, 2011 7:14 pm
Posts: 13
If you think the lock ring is backing off and letting the BB get loose then teflon tape can't help that situation. Are you even sure the lock ring is backing off? If the pinch bolt is propertly tight it almost can't back off. I have 3 Zed cranks and have never had this problem. Make sure all slack is out of the BB by preloading with lock ring then backing off about one eighth turn. There is a hole in the lock ring to help with tighting it and sometimes you have to crank down hard to get slack out of the bearings. When done you should feel a little play at the peddle when you rock back and forth.


Top
   
PostPosted: Wed May 30, 2012 6:30 pm 
Offline

Joined: Tue Mar 22, 2011 5:25 pm
Posts: 7
The LBS tightened the BB earlier in the week and i will only ride it tomorrow morning to see how it is. I felt the lock ring yesterday and i felt that the little allan key bolt on the lock ring was lose. Then i tightened it by clinching it with my hand and turning it clockwise. Then i tightened the allan key. The crank feels a bit tight when i spin it around and halfway through the 360 degree it spins a bit more freely.I think the shop overtightened it on purpose a bit, because it might settle in on the ride and loosen a bit. Does this sound right ?


Top
   
PostPosted: Wed May 30, 2012 7:55 pm 
Offline

Joined: Wed Mar 16, 2011 7:14 pm
Posts: 13
You should take the chain off the small ring so you can spin the crank. Tighten the lockring ring till the crank gets i little hard to spin then back off lockring one eighth turn at a time till the crank spins free all the way around. If you think lockring is backing off put a drop of white paint or nail polish on lockring and crank arm and, after ride see if lockring moved.


Top
   
Posted: Wed May 30, 2012 7:55 pm 


Top
   
 
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 8 posts ] 

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. Oval Concepts 520 crank vs 5750 crank weights?

in Road

kkapdolee

0

791

Thu Dec 17, 2015 8:18 pm

kkapdolee View the latest post

There are no new unread posts for this topic. Crank Length

[ Go to page: 1 2 3 4 ]

in Road

cyclespeed

51

1921

Wed Sep 07, 2016 7:16 am

cyclespeed View the latest post

There are no new unread posts for this topic. Would you ride this crank ?

[ Go to page: 1 2 ]

in Road

trailflow1

15

2331

Mon Dec 21, 2015 6:13 pm

Svetty View the latest post

There are no new unread posts for this topic. New Easton crank...

in Road

uraqt

6

671

Wed Jul 13, 2016 11:29 pm

wiRIDEfast View the latest post

There are no new unread posts for this topic. Attachment(s) SRAM Red Crank Compatibility

in Road

notquiterite

6

992

Sat Dec 19, 2015 12:44 pm

DavidMLee View the latest post


All times are UTC+01:00


Who is online

Users browsing this forum: alpinestar, Bing [Bot], Majestic-12 [Bot], Yahoo [Bot] and 27 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited