Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Blog NEW Galleries NEW FAQ Contact About Impressum
It is currently Thu Oct 19, 2017 9:40 pm

All times are UTC+01:00





Post new topic  Reply to topic  [ 5 posts ] 
Author Message
PostPosted: Tue May 15, 2012 10:00 pm 
Offline
User avatar

Joined: Sun Sep 21, 2008 9:07 pm
Posts: 1084
Location: Slovenia---that forest land
Is there any manuals on internet how to get out bearings?

I get Novatec with industrial bearings and one bad reynolds strike fornt hub.

How i get out bearings?

I find only for rear hub dissasambling

_________________
http://kavitec.blogspot.com/

click this! http://www.youtube.com/watch?v=0m8maAO-m-w


Top
   
PostPosted: Wed May 16, 2012 5:30 am 
Offline

Joined: Thu Oct 13, 2011 5:25 pm
Posts: 169
Once the axle is out, knock them out with some type of punch, striking the inner steel race. Rotate around the hub shell body and use light knocks, and you should feel the bearing begin to come out.

Getting new bearings back in is slightly tricker, since it is possible to toast them if you press them in uneven. It is best to make some sort of bearing press. You can do this using washers, the old bearings, and a threaded axle.


Top
   
Posted: Wed May 16, 2012 5:30 am 


Top
   
 
PostPosted: Wed May 16, 2012 6:44 am 
Offline
User avatar

Joined: Sun Sep 21, 2008 9:07 pm
Posts: 1084
Location: Slovenia---that forest land
on novatec a171sb i tried with rubber hammer to get axle out.

so it need pretty hard punch?

thanks

_________________
http://kavitec.blogspot.com/

click this! http://www.youtube.com/watch?v=0m8maAO-m-w


Top
   
PostPosted: Wed May 16, 2012 7:38 am 
Offline
User avatar

Joined: Sun Sep 21, 2008 9:07 pm
Posts: 1084
Location: Slovenia---that forest land
simple design of front hubs.

I did it. bearings bed was too tight, so beraing was squeezed and has more friction.

_________________
http://kavitec.blogspot.com/

click this! http://www.youtube.com/watch?v=0m8maAO-m-w


Top
   
PostPosted: Sun May 20, 2012 11:00 am 
Offline

Joined: Mon Oct 12, 2009 6:36 pm
Posts: 246
You can use quite a bit of force to get the old bearings out, since you will not be using them anyway. No rubber hammer necessary. When inserting new bearings, I would use a plastic hammer. Also make sure to put a bit of grease on the hub where the bearing will end up. This will make installation (and removal) easier.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 5 posts ] 

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. Reynolds Strike SLG

in Road

poppiholla

0

679

Tue Jan 17, 2017 8:57 pm

poppiholla View the latest post

There are no new unread posts for this topic. How to remove Reynolds freehub Strike SLG wheelset?

in Road

poppiholla

5

557

Fri Jan 20, 2017 11:52 am

poppiholla View the latest post

There are no new unread posts for this topic. Colnago warranty service?

in Road

wilwil

12

1189

Sun Jun 25, 2017 5:48 pm

wilwil View the latest post

There are no new unread posts for this topic. Bianchi and other brands customer service

[ Go to page: 1 2 ]

in Road

Boshk

22

1228

Tue Oct 17, 2017 3:38 pm

MXGimp View the latest post

There are no new unread posts for this topic. Attachment(s) Comparing frame geometries\fit tool\service

[ Go to page: 1 2 ]

in Road

itsacarr

26

2211

Fri May 26, 2017 1:08 pm

itsacarr View the latest post


All times are UTC+01:00


Who is online

Users browsing this forum: Baidu [Spider], benjaminm3, Bing [Bot], jb, JoeFlan, PinaF8, ride1970 and 31 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited