Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Blog NEW Galleries NEW FAQ Contact About Impressum
It is currently Tue Dec 06, 2016 8:48 pm
Recently the board software has been updated and there are some known bugs/failures:
- Avatars are currently not being displayed ✔ FIXED
- Tapatalk connection is currently broken ✔ FIXED
- Avatars cannot be uploaded ✔ FIXED

Please note that we will soon do some changes in WW board template design in case to get a fully mobile/desktop responsiveness board!
If you find more errors please post it here: http://weightweenies.starbike.com/forum/viewtopic.php?f=7&t=139062


All times are UTC+01:00





Post new topic  Reply to topic  [ 38 posts ]  Go to page Previous 1 2 3 Next
Author Message
PostPosted: Fri Jun 21, 2013 2:17 pm 
Offline

Joined: Sat Feb 07, 2009 5:52 am
Posts: 442
The curved Ti plate tore clean off the top of the shaft...the clamp etc was all still attached to the saddle... :roll:[/quote]

Thanks. Now I understand the design flaw. Might be possible to rectify it, but Ti is never going to be forgiving of that kind of flaw.


Top
   
Posted: Fri Jun 21, 2013 2:17 pm 


Top
   
 
PostPosted: Fri Jun 21, 2013 7:51 pm 
Offline
User avatar

Joined: Thu May 04, 2006 4:43 pm
Posts: 5375
Location: Wherever there's a mountain beckoning to be climbed
Alu steerer of Alan alu fork snapped while JRA in the saddle on a modest upgrade at a little under 30 kph. Bike veered diagonally across the road, fortunately with no oncoming traffic, and rode into, up and over a curb, across a sidewalk, and crashed on an upward sloping lawn, just short of a tree. Not fun.


Top
   
PostPosted: Sat Jun 22, 2013 8:04 pm 
Offline

Joined: Sun Nov 14, 2010 10:25 pm
Posts: 482
Was stripping down an old bicycle today that I got for free. The bike sat for 28 years so tires, bar tape and hoods were a bit crunchy.
I was just gonna take of the handlebars and noticed a hairline crack in the quill stem.
Image
Untitled by Quattrings, on Flickr

I decided to see what force it would take to break it, so I hopped aboard and tugged it like a sprinting madman.

Image
Untitled by Quattrings, on Flickr

I wasn't able to break the bolt however so the bars did stay attached.

_________________
  • 2011 Cannondale Flash F1
  • 2010 Cannondale Caad9
  • 2000 Caad 4 aero



Top
   
PostPosted: Sun Jun 23, 2013 10:05 am 
Offline
User avatar

Joined: Sun Dec 21, 2003 8:32 pm
Posts: 1470
Location: WALES,UK
I'm sure 3t will warranty that :D

_________________
Ti or dye!

The Weenie formally known as CAADHEAD


Top
   
PostPosted: Sun Jun 23, 2013 11:25 am 
Offline
User avatar

Joined: Sat Jun 02, 2007 12:48 pm
Posts: 979
Location: Denmark
Cjcc67 wrote:
A titanium bolt snapped on my 3T ARX stem, it was not over torqued. A search after the fact revealed this is common.

Same happened to me. First time installation, used a torque wrench. Bolt snapped.

_________________
------------
If you dream of being famous - think of what birds do to statues.
Instagram: https://www.instagram.com/kermithimself/
Youtube: https://www.youtube.com/channel/UCdCPaXwpeXT_LpuEF0REjqw
Facebook: https://www.facebook.com/gotlegscycling/


Top
   
PostPosted: Sat Jul 06, 2013 9:55 am 
Offline

Joined: Thu Mar 01, 2012 2:10 am
Posts: 312
Snapped the body of my Time RXS pedals
Image
Image
Image


Top
   
PostPosted: Sun Jul 07, 2013 10:25 am 
Offline
in the industry
User avatar

Joined: Fri Jan 23, 2004 6:31 pm
Posts: 373
Selle Italia Flite Ti rail popped out of the thermoplastic body (mid 90's).
Syncross road Quill stem cracked at the quill above the headset collar, thats a lotta torque over time, (mid 90's).
Syncros Ti seat post bent in half, (on Cannondale Super V after a seated landing from a 3 foot bunny hop, mid 90's)
White Industry road Hub cracked rear axle during TOMRV 24 and stayed held together by a Salsa flip off skewer, made one helluva rotational squeaky noise for the last 40 miles (mid 90's).
Mavic CX 117 first SUP rim, laced to Purple Ringle hubs (MID 90's!) would break spokes left and right till it was replaced by a set of Blue Ringle/HED MTB wheels, only wheel I ever broke spokes on, (mid 90's).

So you could say the mid 90's produced a few sh*t parts.

Anything else I ever broke was due to not having a torque wrench, (bolts and such, nothing major).

_________________
carbonLORD.com


Top
   
PostPosted: Wed Jul 10, 2013 6:43 am 
Offline
User avatar

Joined: Wed Oct 20, 2010 5:56 am
Posts: 398
In summer 2010 I let a visitor borrow my spare road bike and near the end of the ride he blew the rear derailleur off. I went back and found the parts on the road. We put it back together and it works fine again. 1980 Campagnolo Nuevo Gran Sport.

I realize this is a "failed parts" thread but I had to tell the story. Truly, it wasn't a parts failure, but a mechanic failure. I hadn't checked the bolts in 20 years or so.


Top
   
 Post subject: Failed parts x 2
PostPosted: Sat Jul 13, 2013 8:56 pm 
Offline
User avatar

Joined: Sat Dec 04, 2010 5:31 pm
Posts: 361
C-4 wheel hubs (front and rear a couple of times) and Look Keo-Blades (cracked near the axle but immediately replaced without question by Competitive Cyclist)


Top
   
PostPosted: Sat Jul 20, 2013 6:29 pm 
Offline
User avatar

Joined: Tue Apr 26, 2011 8:09 pm
Posts: 255
Location: London
I got a new one today...

The steerer on my beloved Slice Si has cracked and delaminated on both the front and back. It has always been torqued to spec. I guess its a combination of harsh road conditions and age. It seems the shim for my Syntace F149 has also marked to steerer.

Image

Image

Image

Shit happens.

Getting an Enve 1.0 :twisted:

_________________
--Max.


Top
   
PostPosted: Sat Jul 20, 2013 8:02 pm 
Offline

Joined: Sun Nov 14, 2010 10:25 pm
Posts: 482
good thing you caught that. Did you notice on some level that something was off?

This is the carbon slice by Time right?

_________________
  • 2011 Cannondale Flash F1
  • 2010 Cannondale Caad9
  • 2000 Caad 4 aero



Top
   
PostPosted: Sat Jul 20, 2013 9:40 pm 
Offline
User avatar

Joined: Tue Apr 26, 2011 8:09 pm
Posts: 255
Location: London
My headset came loose one ride, I tightened it up, happened again. I then thought the expander had slipped up so took the stem off and noticed the crack.

Good thing too as I'm marauding the Alps from Friday.

It is a Time made fork, which is a real shame as it is really light, stiff and ride wonderfully, not to mention the beautiful construction.

_________________
--Max.


Top
   
PostPosted: Sat Jul 20, 2013 9:45 pm 
Offline
User avatar

Joined: Tue Apr 26, 2011 8:09 pm
Posts: 255
Location: London
Image

_________________
--Max.


Top
   
PostPosted: Mon Jul 22, 2013 7:04 am 
Offline

Joined: Tue May 10, 2011 7:36 am
Posts: 56
Image

Ouch.


Top
   
PostPosted: Tue Jul 23, 2013 9:28 pm 
Offline
User avatar

Joined: Mon Jan 23, 2006 6:35 am
Posts: 5072
Location: New York
Maximilian wrote:
I got a new one today...

The steerer on my beloved Slice Si has cracked and delaminated on both the front and back. It has always been torqued to spec. I guess its a combination of harsh road conditions and age. It seems the shim for my Syntace F149 has also marked to steerer.

Shit happens.

Getting an Enve 1.0 :twisted:


I think the torque wrench is your enemy in this case.

_________________
I never took drugs to improve my performance at any time. I will be willing to stick my finger into a polygraph test if anyone with big media pull wants to take issue. If you buy a signed poster now it will not be tarnished later. --Graeme Obree


Top
   
Posted: Tue Jul 23, 2013 9:28 pm 


Top
   
 
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 38 posts ]  Go to page Previous 1 2 3 Next

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. Attachment(s) Show us your leg thread...

[ Go to page: 1 2 3 4 ]

in Cycle Chat

PSM

52

7508

Tue Nov 15, 2016 9:59 pm

PSM View the latest post

This topic is locked, you cannot edit posts or make further replies. Doping Thread

in Cycle Chat

mrgray

2

913

Sat Aug 13, 2016 7:16 am

Frankie - B View the latest post

There are no new unread posts for this topic. already covered in another thread...

in Everything wheels

ultyguy

1

178

Tue Sep 27, 2016 10:07 am

jekyll man View the latest post

There are no new unread posts for this topic. Different spin on a wheel thread

in Everything wheels

abrown3mtg

7

786

Thu Apr 28, 2016 1:59 pm

Svetty View the latest post

There are no new unread posts for this topic. Rivet ti Build Thread

[ Go to page: 1 2 ]

in Introduce Yourself / Gallery - Please use metric weights.

thedonnydino

24

2503

Thu Oct 13, 2016 5:24 am

thedonnydino View the latest post


All times are UTC+01:00


Who is online

Users browsing this forum: JackRussellRacing, nohands and 15 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited