Using carbon brake pads on alloy rims?
Moderator: robbosmans
Any experiences using carbon brake pads on alloy rims?
My wiggle & Reynolds blue pads seem to work ok on alloy, if there are no shavings embedded do you think I can just leave them on when I switch wheels?
My wiggle & Reynolds blue pads seem to work ok on alloy, if there are no shavings embedded do you think I can just leave them on when I switch wheels?
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
No, you should never leave the same pads when switching wheels. Filings from the alu rims, attached to your pads, will definitely harm the carbon surface.
Marin wrote:if there are no shavings embedded
- miltmaster3
- Posts: 830
- Joined: Sun Nov 30, 2008 7:29 pm
- Location: patra greece
Just clean it . My TT bike has the brakes down and it is a difficult to make the change (I have to remove the crank) so I have the carbon pads and when I want to put my disk wheel just clean the pads
in watt mode
in watt mode
πατα τραβα ρε
Really. Even scrubbing and/or filing pads down leaves shards of aluminum in the pad sometimes. And takes far longer than swapping pads.Marin wrote:Marin wrote:if there are no shavings embedded
And what sort of moron designs a bike that you actually need to remove the crank to change brake pads?
- miltmaster3
- Posts: 830
- Joined: Sun Nov 30, 2008 7:29 pm
- Location: patra greece
Shiv TT small size
in watt mode
in watt mode
πατα τραβα ρε
-
- Posts: 1145
- Joined: Sat Dec 07, 2013 10:15 pm
carbon pads are more expensive. what's the point? They might stop better, but were never designed for alloy wheels. Can only imagine unintended consequences.
http://www.visiontechusa.com/brake-pads ... on-wheels/
http://www.visiontechusa.com/brake-pads ... on-wheels/
Colnago C-59 (Dura Ace)
Firefly(Ultegra)
Colnago C-64 disc(ultegra) with Bora 35 wheels
Firefly(Ultegra)
Colnago C-64 disc(ultegra) with Bora 35 wheels
what a mess. Someone needs a talking to!miltmaster3 wrote:Shiv TT small size
Serious hat on for a moment.
Maybe drill a small hole in the chainring so you can get to the brake shoe bolt and release the pad. Put it next to or opposite the crank arm (lowest stress IIRC) but either way, a small neat hole in an aero ring won't make any noticeable difference. And it looks like it should be inside the inner diameter of the inner ring as well.
you can remove the brake pad and shoe from shiv without removing the crank. Just change the alen bolt with a standard 12mm polygon head.
I would never keep the carbon pads for different types of wheelsets. Cleaning pads do not remove very small aluminium shards.
I would never keep the carbon pads for different types of wheelsets. Cleaning pads do not remove very small aluminium shards.
Exactly! Aluminum shards are pushed deep into the brake pads, not visible to naked eye. Long story short, you are damaging you carbon brake track on your carbon wheels.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Racing is a three-dimensional high-speed chess game, involving hundreds of pieces on the board.
CBA = Chronic Bike Addiction
OCD = Obsessive Cycling Disorder
CBA = Chronic Bike Addiction
OCD = Obsessive Cycling Disorder
Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓ Broad Selection ✓ Worldwide Delivery ✓
www.starbike.com
Just ditch the retaining screw and don't try to use the brakes while riding backwards!
You probably have to adjust the brake pad contact from wheel to wheel anyway so you might as well swap the pads.
You probably have to adjust the brake pad contact from wheel to wheel anyway so you might as well swap the pads.