HOT: Active* forum members generally gain 5% discount at store!
Weight Weenies
* FAQ    * Search    * Trending Topics
* Login   * Register
HOME Listings Blog NEW Galleries NEW FAQ Contact About

Post new topic Reply to topic  [ 25 posts ] 
Go to page Previous  1, 2
Author Message
PostPosted: Sat Jul 21, 2012 1:32 am 

Joined: Fri May 25, 2012 6:02 pm
Posts: 90
I know I might get my WW card revoked for saying this, but I no longer ride ti skewers - I want my wheels as stiff as possible, and I want my wheels clamped down as securely as possible. So all I use now are DT Swiss RWS skewers - steel with aluminum lever. Front weighs 51g and rear comes in at 55g. Nothing clamps as strongly as these suckers.



S5 VWD | 9070 di2 | Pioneer PM | Enve 3.4s/6.7s
Cannondale SuperX Hi-Mod Disc | Sram Red | Pioneer PM | Zipp 303s
P5 | 9070 di2 | TriRig Alpha/Sigma | Pioneer PM | Zipp 808/Super 9 Disc
T1 | Scatto | Rolf Prima FX58/Zipp Super 9 Disc

PostPosted: Sat Jul 21, 2012 1:48 am 

Joined: Mon May 16, 2011 8:14 pm
Posts: 365
I'm using Tune Dc-14's and love them. I'm 200 lbs, ride out of the saddle often, and am on non-stop large hills here in VT. The only issue I have is that I need to make sure the rear wheel is tight in the drop-out before every ride. On a couple rare occasions, the rear wheel has shifted ever so slightly - just enough for me to notice a decrease in shifting crispness. But checking the QR before every ride is no big deal to me. I feel no real flex; and certainly I'm not having the wheels rub the brakes at any point in time. Unlike other super lightweight QR's which you may have to be careful with the amount of force you clamp down with - Tune states in the instructions that you may clamp down as hard as your heart desires - and that the skewer can take it..!

Posted: Sat Jul 21, 2012 1:48 am 

PostPosted: Sat Jul 21, 2012 2:07 am 
User avatar

Joined: Sat Aug 13, 2011 9:43 am
Posts: 38
Location: Adelaide
I've found a happy "middle ground" with Tune AC14 skewers. At 48g you're only taking a tiny 15g hit over the DC14s but gaining an internal cam clamping mechanism (like Shimano/Campy) which holds the wheels in very securely. I am 220lb and race and train on these with no issues.

IME the internal clamping mechanism is much more reliable and consistent than the external mechanism of the POP or tune DC14. I broke a POP external clamp trying to get decent clamping force. No issues with the AC14, over 10000km trouble free. The wheels never move no matter how hard I ride/corner. As VTBike indicates, I too noticed the rear wheel could move slightly sometimes when using external mechanism shewers. With the AC14s, the clamping force is maintained until you release it. I have checked many times and there is no loss of force with use.

"Bite off more than you can chew, then chew like hell." Peter Brock.

PostPosted: Sat Jul 21, 2012 2:38 pm 

Joined: Tue Jun 22, 2004 11:42 pm
Posts: 3915
Location: lat 38.9677 lon 77.3366
Even at my weight I have had no issues for the last 5 years using skewers as light as 48 grams for the pair. They are perhaps a bit more fussy in use. These days I mostly just use the Campy skewers, my average speed has not gone down BTW :shock:

WW Velocipedist Gargantuan

PostPosted: Sat Jul 21, 2012 2:51 pm 

Joined: Sat May 26, 2012 11:26 pm
Posts: 607
So are people complaining about the cam design of lightweight skewers causing the rear wheel to move relative to the dropout under load or flex in the ti axle causing the wheel to move relative to the dropout under load?

Evo 5.63kg SL3 6.66 viewtopic.php?f=10&t=110579" onclick=";return false;" onclick=";return false;

→ Custom Sanded and Clear-coated Black & Gold Evo

PostPosted: Sat Jul 21, 2012 3:09 pm 

Joined: Sun Oct 05, 2008 8:09 pm
Posts: 1230
Location: Aix en Provence
Campy skewers for me too. I like a solid connection in that spot.

PostPosted: Sat Jul 21, 2012 7:00 pm 

Joined: Tue Jun 28, 2011 10:43 pm
Posts: 199
I've run most decent QRs. never had any problems.

I currently have a pair of mt zoom ti and a pair of kcnc ti on road and MTb and had no problems at all. If the QR doesn't have a cam, then you need to tighten them up a little more.

Really quite supprised there is some much negative about light QR, unless in general either I always do my QRs up too tight, or those that have experienced problems have in general not been doing theirs up enough.....

PostPosted: Sat Aug 16, 2014 4:25 pm 
User avatar

Joined: Sun Feb 23, 2014 4:45 pm
Posts: 24
I wanted to order some titanium ENVE skewers (steel is not available), but after reading something about titanium rods stretching very easily and external cam skewers not clamping as good as internal ones.. are 'fancy' skewers worth it? or should i just check my lbs for some Shimano skewers which have always worked fine. Zipp (steel) skewers are easily available as well but are external.

Couldn't find any threat regarding this.

PostPosted: Sun Aug 17, 2014 2:23 am 

Joined: Tue Nov 11, 2003 9:47 pm
Posts: 2056
Location: Santa Cruz, California, USA
Depends on your needs. And on the skewers. I have used both internal and external cam skewers that did not work very well. But the external cam design tends to make skewers that don't clamp as well as internal cam.

I've not noticed any of my Ti skewers stretching.

I've had good luck with Kcnc Ti external cam skewers. But the levers on those are short so you need to keep that in mind and really crank them down. I've also had some Chinese external cam Ti skewers work well... and some not so well.

But if it's not a WW bike, Dura Ace skewers are the gold standard. Heavier than the WW skewers but they do clamp well.

PostPosted: Sun Aug 17, 2014 2:33 am 

Joined: Tue May 23, 2006 9:39 pm
Posts: 513
i have Enve skewers on both bikes with no noticeable stretching on titanium rods. besides, i take my wheel off and on all the time and readjust tightness then, so no issues.

- AX Lightness Vial EVO D + DA9070 + Enve SES 4.5 CK hubs
- Parlee Z5 SLi + DA9070 + Enve 3.4 Tune/Dash hubs
- Parlee ESX + DA9070 + Enve SES 6.7 CK hubs
- Independent Fabrication Ti FLW + Campy SR11 + Enve 3.4 CK hubs

Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 25 posts ] 
Go to page Previous  1, 2

Who is online

Users browsing this forum: BeeSeeBee and 4 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

   Similar Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. Internal vs external cam skewers

in Road




Thu Feb 26, 2015 8:26 pm

Tom-s View the latest post

There are no new unread posts for this topic. How tight j&l titanium bolt on skewers

in Road




Wed Jun 24, 2015 7:29 am

Marin View the latest post

There are no new unread posts for this topic. Attachment(s) GP4000s measure 27mm on 14mm internal / 19mm external width

[ Go to page: 1, 2 ]

in Road




Sat Oct 24, 2015 2:00 am

rpenmanparker View the latest post

There are no new unread posts for this topic. Looking for Lightest Internal Cam QR Skewers like this pic

in Road




Mon May 25, 2015 3:00 pm

Joso View the latest post

There are no new unread posts for this topic. Stainless vs chromoly skewers - least flex

[ Go to page: 1, 2, 3 ]

in Road




Mon Nov 09, 2015 11:23 am

Titanium22 View the latest post

It is currently Sun Nov 29, 2015 4:30 am

All times are UTC + 1 hour

Advertising   –  FAQ   –  Contact   –  Convert   –  About

© Weight Weenies 2000-2013
hosted by

How to get rid of these ads? Just register!

Powered by phpBB

-10% on AX Lightness        Discunt will be shown / added at the shopping basket. NOT combinable with regular WW discount!
▹ Nasdorowje
▹ Premium Road 38 tubular
▹ Leaf carbon saddle with leather cover
▹ Vial Evo carbon frame "D" with THM Scapula CT fork